P42BN820MA04679T Knowles

Opti-Cap Ultra Broadband DC Blocking Features l X7R temperature and voltage stability l Resonance free DC blocking to >40GHz l SMT by solder or epoxy bonding l Low frequency stability over temperature l Very low series inductance l 0201, 0402 and 0602 footprints Functional applications l Test Equipment, Photonics, SONET, TOSA/ROSA, High Speed Data l Broadband Microwave/Millimeter Wave l Transimpedance Amplifiers Specification Electrical Temperature Coefficient of Capacitance X5R: -55C to +85C (TCC 15%) X7R: -55C to +125C (TCC 15%) Insertion Loss Capacitance Range 1.5nF to 220nF 0.2 Maximum Assembly Process Temperature 250C 0 Milli-Cap : GHz Range -0.2 -0.4 Multilayer Capacitor:KHzMHz Range -0.6 P21BN300MA03976 -0.6 P42BN820MA03152 -1 P62BN820MA02636 -1.2 05 10 15 20 25 30 35 40 Frequency (GHz) Electrical characteristics - Opti-Cap Capacitance Voltage DF IR Frequency Part Number TCC Rating (Max) (Min) Range MLC Milli-Cap 2 P21BN300MA04733 100nF 30pF 3.5% >10 M 2 P21BN300MA04282 22nF 30pF 10V X5R 3.5% >10 M www.dilabs.com 2 P21BN300MA03976 10nF 30pF 3.5% >10 M North America 16KHz - 2 P21BN300MA04678 1.5nF 30pF 25V X7R 3.5% >10 M Knowles (Cazenovia) >40GHz 2 Phone: +1 315 655 8710 P42BN820MA03152 220nF 82pF 10V X5R 3.5% >10 M DLISales knowles.com 2 P42BN820MA04679 22nF 82pF 50V X7R 3.5% >10 M Europe 2 P62BN820MA02636 100nF 82pF 25V X7R 3.5% >10 M Knowles (UK) Ltd Phone: +44 1603 723300 SyferSales knowles.com Far East Knowles Capacitors Phone: +86 512 62588258-6243 KCAsiaSales knowles.com 10104/17/v4 Magnitude (dB)Dimensional specifications - Opti-Cap Milli-Cap MLC Case size Length Width Thickness Length Width Thickness P21 (0201) 0.020 0.004 0.012 0.002 0.010 0.002 0.022 0.002 0.010 0.001 0.010 0.002 P42 (0402) 0.038 0.004 0.020 0.002 0.020 0.002 0.040 0.002 0.020 0.002 0.020 0.002 P62 (0602) 0.058 0.004 0.020 0.002 0.020 0.002 0.067 0.004 0.031 0.004 0.031 0.005 Attachment Methods - Opti-Cap Recommended attachment to soft or hard substrate using Conductive Epoxy 1. Place a single drop of conductive epoxy onto each micro strip as illustrated the edge of the epoxy shall be at least .003- .004 back from the edge of the trace to prevent filling the gap with epoxy. 2. Centering the termination gap of the capacitor within the gap in the micro strip, press with careful, even pressure onto the micro strip ensuring the terminations make good contact with the epoxy drops. 3. Cure according to the epoxy manufacturers preferred schedule, typically 125C to 150C max. 4. After curing, inspect joint for epoxy shorts across the termination and micro strip gaps that would cause a short across the cap. Isopropanol and Methanol are both safe to use to pre clean Opti-Caps . Isopropanol, and Methanol are not to be used after mounting with conductive epoxy as they act as a solvent Recommended attachment to soft or hard substrate using Solder 1. Place a single drop of solder paste onto each micro strip as illustrated the edge of the solder shall be at least .001- .002 back from the edge of the trace to prevent filling the gap with solder. 4. After the reflow step is completed, inspect joint for voids or 2. Centering the termination gap of the capacitor within the gap excess flux and non-reflowed solder balls that can degrade performance or cause shorts across the gaps. in the micro strip, press with careful, even pressure onto the micro strip ensuring the terminations make good contact with Proper cleaning after the reflow process is crucial to avoiding performance degradation and discovering poor solder the drops of solder paste. joints. 3. Reflow according to the solder manufacturers preferred profile, ensuring the reflow temperature does not exceed Isopropanol and Methanol are both safe to use with soldered Opti-Caps . 250C. 10104/17/v4 Copyright: Knowles Corporation 2017 - Design: www.panpublicity.co.uk