HPC ceramic resistors for anti pulse surge EU features KOA original bulk ceramic resistors Excellent in anti-pulse characteristics Higher reliability against disconnection compared to wirewound resistors and film resistors Products with lead-free terminations meet EU RoHS requirements. RoHS regulation is not intended for Pb-glass contained in the electrode. Non-inductive resistors AEC-Q200 Qualified dimensions and construction Dimensions inches (mm) Inner Type L D d (nom.) l* Electrode Resistive .433.039 .138.039 Body HPC1/2 Marking Electrode (11.02.0) (3.51.0) Cap Coating 0.630.039 .177.039 HPC1 (16.02.0) (4.51.0) .031 10K (0.8) Lead .827.039 .197.039 HPC2 3mm Max. Wire (21.02.0) (5.01.0) 1.50.118 L D (38.03.0) 1.02.039 .236.039 HPC3 (26.02.0) (6.01.0) 1.50.039 .276.039 HPC4 (38.02.0) (7.01.0) .039 Derating Curve (1.0) 1.73.039 .295.039 HPC5 100 (44.02.0) (7.51.0) 80 * Lead length changes depending on taping type 60 For resistors operated at an ambient temperature of 40C 40 or above, a power rating shall be 20 derated in accordance with the derating curve. 0 -60 -40 -20 0 20 6080100 120 140 160180 200 40 Ambient Temperature (C) ordering information HPC 1/2 C T631 R 103 K Power Termination Nominal Type Taping Packaging Tolerance Rating Material Resistance HPC 1/2: 0.5W C: SnCu 1/2: T52 A: Ammo 2 significant K: 10% figures + 1 1: 1W 1: T631 R: Reel M: 20% multiplier 2: 2W 3: 3W 4: 4W 5: 5W taping Axial Taping Type T52 T631 HPC1/2 HPC1 Contact us for lead forming details. For further information on packaging, please refer to Appendix C. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 10/29/18 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com 163 % Rated Power d leaded resistorsleaded resistors HPC ceramic resistors for anti pulse surge applications and ratings Resistance Range () Power Rated Operating Maximum Maximum Part T.C.R. Rating Ambient Temp. Working Overload -6 Designation K: 10% M: 20% (x10 /K) 40C Temp. Range Voltage Voltage E-12 E-6 HPC1/2 0.5W 200V 400V -500 ~ -1300: 3.3R<10 HPC1 1.0W 300V 600V -600 ~ -1500: 10R<100 -40C HPC2 2.0W 400V 800V -700 ~ -1800: 100R<1k +40C to 10 - 390K 3.3 - 330K -900 ~ -1900: 1kR<100k HPC3 3.0W 450V 900V +200C -900 ~ -2000: 100kR<200k HPC4 4.0W 500V 1000V -900 ~ -2200: 200kR390k HPC5 5.0W 550V 1100V Rated voltage = Power Rating X Resistance Value or Max. working voltage, whichever is lower environmental applications Performance Characteristics Requirement R (% + 0.05 ) Parameter Test Method Limit Typical Resistance Measurement voltage 3.3=<R<10 0.3V Within regulated Resistance 25C to tolerance 10=<R<100 1.0V 100=<R=<390k 3.0V -500~-1300:3.3R<10 -600~-1500:10R<100 -700~-1800:100R<1k T.C.R +25C/-40C and +25C/+125C -900~-1900:1kR<100k -900~-2000:100kR<200k -900~-2200:200kR390k 0~-0.2%/V (HPC1/2) Voltage Coefficient Rated voltage and rated voltage x 10% 0~-0.1%/V (HPC1) (Apply for over 1k) 0~-0.05%/V (HPC2,3,4,5) Overload 2% 0.4% Rated voltage x 2.5 or maximum overload voltage for 5s, whichever less The resistor mounted to the test circuit as below is applied with high voltage impulse 10,000 cycles. Performance Requirements Type Test Voltage R (% + 0.05) 8kV:3.3R<30k 5 HPC1/2 8kV:30kR<390k 10 1 sec ON 5kV:30kR<390k 5 SW Refer to the table on Protection 1 sec OFF Resistance to pulse 15kV:3.3R<30k 5 resistor the right HPC1 15kV:30kR<390k 10 Rx DC 7kV:30kR<390k 5 C=1.000pF (HPC: In (Max. pulse insulation oil) 25kV:3.3R<30k 5 voltage) HPC2 25kV:30kR<390k 10 15kV:30kR<390k 5 HPC3 25kV 5 HPC4 HPC5 Resistance to soldering heat 2% 0.8% 350C10C, 3.5s0.5s Rapid change of temperature 2% 0.4% -40C(30min.)/+85C(30min.), 5 cycles Moisture resistance 5% 0.6% 40C2C, 90%~95%RH, 1000 hours, 1.5h ON/0, 5h OFF cycles Load life 5% 0.4% 40C2C, 1000h, 1.5h ON/0, 5h OFF cycles No abnormality in Dipping in IPA or Xylene for 3 minutes and leaving for 10 minutes after removing drops, Resistance to Solvent appearance. Marking then brushing 10 times. shall be easily legible. High Temperature Exposure 5% 1.7% +200C, 1000 hours Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 11/20/17 164 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com