PSI, PSE chip type power shunt resistor EU features Smooth current flow, suitable for large current detecting Flat structure, applicable for strong mounting Automatic mounting machines are applicable Products with lead-free terminations meet EU RoHS and China RoHS requirements AEC-Q200 Qualified dimensions and construction Dimensions inches (mm) PSE Type Resist. (Inch Size Code) () L W d t L 3.0m .394.010 .205.010 .079.010 PSI .028.010 (10.00.25) (5.20.25) (2.00.25) W (3920) (0.70.25) 4.0m Electrode: 0.5m, .026.010 1.0m (0.650.25) Cu Metal .252.010 .252.010 .087.010 PSE t (6.40.25) (6.40.25) (2.20.25) (2525) Solder 1.5m, .019.010 2.0m (0.500.25) Resin d Resistive Element: Metal Alloy PSI L W Electrode: Cu Metal t Solder d Resistive Element: Metal Alloy NOT RECOMMENDED FOR NEW DESIGN RECOMMENDED REPLACEMENT PSJ2, TLR3AP ordering information PS I D TEB 3L00 F Power Termination Nominal Type Packaging Tolerance Rating Material Resistance I: 3W D: SnAgCu TE: embossed plastic 1%: 4 digits F: 1% (PSE: 2,000 pieces/reel) E: 3W J: 5% 5%: 3 digits TEB: embossed plastic E: 5W All values less than (PSI: 3,000 pieces/reel) 0.1 (100m) are expressed in m with L as decimal Ex: 1m = 1L00 For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 9/30/19 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com 119 current sensecurrent sense PSI, PSE chip type power shunt resistor applications and ratings Resistance T.C.R. Rated Operating Part Power Range (ppm/C) Terminal Part Temperature Designation Rating Max. Temperature Range F: 1% J: 5% PSI 3W 50 3m, 4m +105C 3W +105C -65C to +155C 0.5m, 1.0m 0.5m, 1m, 0.5m, 1m: +105C PSE 150 1.5m, 2.0m 1.5m, 2m 1.5m: 85C 5W 2m: +70C environmental applications Derating Curve PSI, PSE (3W) PSE (5W) 100 100 1.5m 80 80 0.5m 1m 2m 60 60 40 40 20 20 0 0 -60 -40 -20042006080 100 120 140 -60 -40 -20042006080 100 120 140 -65 105 155 -65 70 85 105 155 Terminal Part Temperature Terminal Part Temperature (C) (C) For resistors operated at a terminal part temperature of described for each size or above, a power rating shall be derated in accordance with the derating curve. Please refer to Introduction of the derating curve based on the terminal part temperature in the beginning of our catalog before use. Performance Characteristics Requirement R % Parameter Limit Typical Test Method Within specified T.C.R. +25C/+100C T.C.R. 0.2%: PSI 0.1%: PSI Overload (Short time) 15W for 5 seconds 0.5%: PSE 0.2%: PSE Resistance to Solder Heat 0.5% 0.1% 260C 5C, 15 seconds 1 second Rapid Change of Temperature 0.5% 0.2% -55C (30 minutes), +125C (30 minutes), 1,000 cycles Moisture Resistance 0.5% 0.2% 85C 2C, 85% RH, 1000 hours, 10% Bias Terminal part temperature: 105C (PSI, PSE (3W), PSE (5W) 0.5m, 1.0m) +85C (PSE (5W) 1.5m) Endurance at and Less of 0.2%: PSI 1.0% +70C (PSE (5W) 2.0m), Terminal Part Temperature 0.6%: PSE 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle 0.02%: PSI Low Temperature Exposure 0.5% -65C, 96 hours 0.1%: PSE 0.4%: PSI High Temperature Exposure 1% +155C, 1,000 hours 0.6%: PSE Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 11/26/16 120 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com % Rated Power % Rated Power