resistors RN73H high heat resistance, high reliability metal film chip resistor EU features High precision type 0.05% is available with standard products Improved moisture resistance by glass passivation layer High reliability and high stability at elevated temperatures Low current noise Products with lead-free terminations meet EU RoHS requirements Rated ambient temperature: 85C, rated up to +155C AEC-Q200 Qualified: 0402 (1E), 0603 (1J), 0805 (2A), 1206 (2B), 1210 (2E) dimensions and construction Type Dimensions inches (mm) (Inch Size Code) L Wc d t L c c +.004 +.002 .039 .010 1E -.002 .020.002 .010.004 -.004 .014.002 +0.1 +0.05 (0402) (0.50.05) (0.250.1) (0.350.05) (1.0 ) (0.25 ) -0.05 -0.1 W Solder 1J .063.008 .031.004 .012.004 .012.004 .018.004 Plating (0603) (1.60.2) (0.80.1) (0.30.1) (0.30.1) (0.450.1) Ni t +.008 Plating .012 .049.008 2A .079.008 .016.008 -.004 .02.004 (1.250.2) (0805) (2.00.2) (0.40.2) +0.2 (0.50.1) (0.3 ) d Protective Resistive Inner -0.1 Coating Film Electrode 2B .063.008 +.008 Ceramic (1206) .016 (1.60.2) .126.008 .02.012 -.004 .024.004 Substrate +0.2 (3.20.2) (0.50.3) (0.60.1) 2E .098.008 (0.4 ) -0.1 (1210) (2.50.2) Derating Curve 100 100 80 80 1E (90C) 1J (95C) 2A (100C) 60 60 2B, 2E (110C) 40 40 20 20 0 0 -60 -40 -20 0 20 40 60 80 100 120 140 160 -60 -40 -200420060 80 100 120 140 160 -55 90 95 110 155 -55 85 155 Terminal Part Temperature Ambient Temperature (C) (C) For resistors operated terminal part temperature of described for each size For resistors operated at an ambient temperature of 85C or above, a or above, a power rating shall be derated in accordance with derating curve. power rating shall be derated in accordance with the above derating curve. Please refer to Introduction of the derating curves based on the terminal part temperature in the beginning of our catalog before use. ordering information RN73H T TD 1002 B 25 2B Termination Nominal Resistance T.C.R. Type Packaging Size Material Resistance Tolerance (ppm/C) T: Sn TP: 0402 only: 7 2mm pitch 3 significant A: 0.05% 05 1E: 0.063W punched paper figures + 1J: 0.1W G: Au (1E, B: 0.1% 10 TD: 0603, 0805, 1206, 1210: 1 multiplier 1J only) 2A: 0.125W C: 0.25% 25 7 4mm pitch punched paper R indicates D: 0.5% 50 2B: 0.25W TDD: 0603, 0805, 1206, decimal on 1210: 10 paper tape value <100 F: 1.0% 100 2E: 0.25W TE: 0805, 1206, 1210: 7 embossed plastic TED: 0805, 1206, 1210: 10 embossed plastic For further information on packaging, please refer to Appendix A Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 10/23/15 40 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com % Rated Power % Rated Power RN73H high heat resistance, high reliability metal film chip resistor applications and ratings Rated Resistance Range () Power Rated T.C.R. Maximum Maximum Part Terminal E-24, E-96, E-192* Rating Ambient (ppm/C) Working Overload Designation Part 85C Temp. Max. Voltage Voltage (A0.05%) (B0.1%) (C0.25%) (D0.5%) (F1.0%) Temp. 10 47 - 10k 47 - 10k 47 - 10k 47 - 10k 1/16W 85C 90C 25 47 - 300k 47 - 300k 47 - 300k 47 - 300k 50V 100V RN73H1E (.063W) 50 47 - 300k 47 - 300k 10 - 300k 10 - 300k 5 100 - 59k 100 - 59k 10 47 - 59k 47 - 360k 47 - 360k 47 - 360k 47 - 360k 1/10W RN73H1J 85C 95C 25 47 - 59k 15 - 1M 15 - 1M 10 - 1M 10 - 1M 75V 150V (.10W) 50 15 - 1M 15 - 1M 10 - 1M 10 - 1M 100 10 - 1M 10 - 1M 5 100 - 100k 100 - 100k 47 - 100k 47 - 1M 10 47 - 1M 47 - 1M 47 - 1M 1/8W RN73H2A 85C 100C 25 47 - 100k 15 - 1.5M 15 - 1.5M 10 - 1.5M 10 - 1.5M 150V 300V (.125W) 50 15 - 1.5M 15 - 1.5M 10 - 1.5M 10 - 1.5M 10 - 1.5M 10 - 1.5M 100 100 - 300k 5 100 - 300k 10 47 - 300k 47 - 1M 47 - 1M 47 - 1M 47 - 1M 1/4W RN73H2B (.25W) 85C 110C 25 47 - 300k 15 - 1M 15 - 1M 10 - 1M 10 - 1M 200V 400V 50 15 - 1M 15 - 1M 10 - 1M 10 - 1M 10 - 1M 10 - 1M 100 10 100 - 510k 100 - 510k 100 - 510k 100 - 510k 100 - 510k 25 51 - 510k 10 - 1M 10 - 1M 1/4W 15 - 1M 15 - 1M RN73H2E 200V 400V (.25W) 15 - 1M 15 - 1M 10 - 1M 10 - 1M 85C 110C 50 100 10 - 1M 10 - 1M * No marking on E-192 values Operating Temperature: -55C to +155C environmental applications Performance Characteristics Requirement R (%+0.05 ) Parameter Limit Typical Test Method Resistance Within specified tolerance 25C -6 T.C.R. Within specified T.C.R. +25C/+125C: T.C.R. +5 (x10 K) +15C/-55C and +25C/+155C: other Overload (Short time) 0.05% 0.01% Rated Voltage x 2.5 or Max. overload voltage, whichever is less for 5 seconds Resistance to Solder Heat 0.05%* 0.01% 260C 5C, 10 seconds 1 second 1E, 1J, 2A: -55C (30 minutes), +155C (30 minutes), 1000 cycles Rapid Change of Temperature 0.1%* 0.02% 2B, 2E: -55C (30 minutes), +155C (30 minutes), 500 cycles Moisture Resistance 0.1%* 0.05% 85C 2C, 85%5%RH, 1000 hours 1.5 hr ON, 0.5 hr OFF cycle Endurance at 85C 0.1%* 0.03% 85C 2C, 3000 hours, 1.5 hr ON, 0.5 hr OFF cycle High Temperature Exposure 0.1%* 0.05% +155C, 1000 hours * Depends on resistance value, please contact KOA Speer for details. Precautions for Use The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top tapes to cause a failure in the mounting and the parts are destructed by static electricity (1J, 2A, 2B, 2E: 1kV and more, 1E: 0.5kV and more at Human Body Model 100pF, 1.5k) to change the resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the excessive static electricity when mounting on the boards. Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na), chlorine (Cl) etc. Therefore these kinds of ionic substances may induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances. Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion. Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down. Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat. Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5~35C/35~75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability. The upper electrodes could be peeled off when a heat-resistant masking tape is attached to the mounted chip resistors and then detached from them. It is confirmed that the adhesiveness gets stronger due to the exposure to heat under mounting. Accordingly, we recommend the use of masking tape be refrained. If the use of heat-resistant masking tape is unavoidable, please make sure that the adhesives on the tape do not directly come in contact with the product. For Surface Temperature Rise Graph see Environmental Applications. Additional environmental applications can also be found at www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 11/06/17 KOA Speer Electronics, Inc. 199 Bolivar Drive Bradford, PA 16701 USA 814-362-5536 Fax: 814-362-8883 www.koaspeer.com 41 resistors