Radial Lead Fuses TE5 > Medium Time-Lag Fuse > 398 Series Pb RoHS 398 Series, TE5 Modul Protector Fuse Description The 398 Series TE5 Fuses are short circuit protectors, medium Time-Lag type, and 65V rated. Features Reduced PCB space Flame resistant requirements encapsulated casing Highly defined cut-off Available from 0.125A times to 4A Low internal resistance Halogen free, Lead-free and RoHS compliant Applications Agency Approvals Microprocessor protection Agency Agency File Number Ampere Range E67006 0.125A - 4A Additional Information Electrical Characteristics % of Ampere Rating Opening Time 300 10 Seconds, Max. Samples Datasheet Resources Electrical Characteristics Cold Power Melting Agency Nominal Cold Rated Marking Voltage Resistance Disspation Integral Approvals Amp Code Breaking Capacity Resistance Current Code* Rating 0.1I typ. 1.0I max. 10I max. N N N (Ohms) 2 (m) (mW) (A s) 0125 125mA MP13 65V 0.9610 900 50 0.036 x 0250 250mA MP25 65V 0.3540 355 50 0.063 x 0315 315mA MP32 65V 0.2600 261 60 0.08 x 0400 400mA MP40 65V 0.1860 186 75 0.18 x 0500 500mA MP50 65V 0.1540 155 90 0.33 x 0630 630mA MP63 65V 0.1150 115 120 0.48 x 0800 800mA MP80 65V 0.0850 85 140 1.02 x 50A 65 VAC/DC 1100 1.00A MP100 65V 0.0640 65 170 1.10 x 1125 1.25A MP125 65V 0.0480 48 210 2.34 x 1160 1.60A MP160 65V 0.0340 34 320 4.66 x 1200 2.00A MP200 65V 0.0260 26 425 8.40 x 1250 2.50A MP250 65V 0.0210 21 550 14.81 x 1315 3.15A MP315 65V 0.0155 16 650 29.27 x 1400 4.00A MP400 65V 0.0120 12 1000 41.12 x Notes: 1. 1.00 means the number one with two decimal places. 1,000 means the number one thousand. 2. Resistance is measured at 10% of rated current, 25C. * Physical Marking on top of the device 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.11/14/20Radial Lead Fuses TE5 > Medium Time-Lag Fuse > 398 Series Temperature Re-rating Curve Average Time Current Curves Note: 1. Rerating depicted in this curve is in addition to the standard derating of 25% for continuous operation. Soldering Parameters - Wave Soldering Recommended Process Parameters: 300 280 260 Wave Parameter Lead-Free Recommendation 240 220 Preheat: 200 (Typical Industry Recommendation) (Depends on Flux Activation Temperature) 180 Temperature Minimum: 100C 160 Temperature Maximum: 150C 140 120 Preheat Time: 60-180 seconds 100 Solder Pot Temperature: 260C Maximum 80 Solder Dwell Time: 2-5 seconds 60 40 Recommended Hand-Solder Parameters: 20 0 Solder Iron Temperature: 350C +/- 5C Time (Seconds) Heating Time: 5 seconds max. Cooling Time Preheat Time Dwell Time Note: These devices are not recommended for IR or Convection Reflow process. 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.11/14/20 Temperature (C) - Measured on bottom side of board 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240