Two-chip SIDACtor Device RoHS The two-chip SIDACtor design provides a through-hole technology protection solution. It is 1 intended for telecom applications that do not require a balanced solution. For primary (T) 2 protection applications, devices with higher holding current and integrated failsafe options (G) 3 (R) are available. SIDACtor devices enable equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters V V V V DRM S DRM S Volts Volts Volts Volts Part V I I I I T DRM S T H Number * Pins 1-2, 3-2 Pins 1-3 Volts Amps mAmps Amps mAmps P0602A L 25 40 50 80 4 5 800 2.2 50 P1402A L 58 77 116 154 4 5 800 2.2 150 P1602A L 65 95 130 190 4 5 800 2.2 150 P2202A L 90 130 180 260 4 5 800 2.2 150 P2702A L 120 160 240 320 4 5 800 2.2 150 P3002A L 140 180 280 360 4 5 800 2.2 150 P3602A L 170 220 340 440 4 5 800 2.2 150 P4202A L 190 250 380 500 4 5 800 2.2 150 P4802A L 220 300 440 600 4 5 800 2.2 150 P6002A L 275 350 550 700 4 5 800 2.2 150 * L in part number indicates RoHS compliance. For non-RoHS compliant device, delete L from part number. For individual AA, AB, and AC surge ratings, see table below. General Notes: All measurements are made at an ambient temperature of 25 C. I applies to -40 C through +85 C temperature range. PP I is a repetitive surge rating and is guaranteed for the life of the product. PP Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. V is measured at I DRM DRM. V is measured at 100 V/s. S Special voltage (V and V ) and holding current (I ) requirements are available upon request. S DRM H Surge Ratings in Amps I PP 0.2x310 * 2x10 * 8x20 * 10x160 * 10x560 * 5x320 * 10x360 * 10x1000 * 5x310 * I TSM 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 ** 10x560 ** 9x720 ** 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz di/dt Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps/s A 20 150 150 90 50 75 75 45 75 20 500 B 25 250 250 150 100 100 125 80 100 30 500 C 50 500 400 200 150 200 175 100 200 50 500 * Current waveform in s ** Voltage waveform in s Telecom Design Guide 2006 Littelfuse 3 - 45 www.littelfuse.com Series SIDACtor DevicesTwo-chip SIDACtor Device Thermal Considerations Package Symbol Parameter Value Unit T Operating Junction Temperature Range -40 to +150 C J Modified T Storage Temperature Range -65 to +150 C S TO-220 R Thermal Resistance: Junction to Ambient 50 C/W JA PIN 1 PIN 3 PIN 2 Capacitance Values pF pF Pin 1-2 / 3-2 Pin 1-3 Tip-Ground, Ring-Ground Tip-Ring Part Number MIN MAX MIN MAX P0602AAL 15 145 10 90 P0602ABL 15 250 10 145 P0602ACL 25 250 10 145 P1402AAL 40 60 20 35 P1402ABL 40 155 20 90 P1402ACL 55 155 30 90 P1602AAL 35 60 20 35 P1602ABL 35 145 20 85 P1602ACL 45 145 25 85 P2202AAL 30 50 15 30 P2202ABL 30 115 15 65 P2202ACL 45 115 25 65 P2702AAL 25 45 15 25 P2702ABL 25 105 15 60 P2702ACL 40 105 20 60 P3002AAL 25 40 15 25 P3002ABL 25 95 15 55 P3002ACL 35 95 20 55 P3602AAL 25 35 10 20 P3602ABL 25 90 10 50 P3602ACL 35 90 15 50 P4202AAL 25 35 10 20 P4202ABL 25 85 10 50 P4202ACL 30 85 15 50 P4802AAL 20 35 10 20 P4802ABL 20 85 10 50 P4802ACL 30 85 15 50 P6002AAL 20 35 10 20 P6002ABL 20 80 10 45 P6002ACL 30 80 15 45 Note: Off-state capacitance (C ) is measured at 1 MHz with a 2 V bias. O www.littelfuse.com 3 - 46 2006 Littelfuse Telecom Design Guide