Q6012NH1LEDRP Littelfuse

Thyristors 12 Amp Alternistor (High Commutation) Triac for LED dimmer Application RoHS Q6012xH1LED Series Description Q6012xH1LED series is designed to meet low load current characteristics typical in LED lighting applications. By keeping holding current at 8mA maximum, this Triac series is characterized and specified to perform best with LED loads. The Q6012xH1LED series is best suited for LED dimming controls to obtain the lowest levels of light output with a minimum probability of flickering. Agency Approval Features R o H S - c o m p li a nt 2 5 0 0 V min isolation Agency Agency File Number AC between mounting tab A s low as 8mA max E71639* and active terminals holding current * - L Package only I mproves margin of safe L -Package is UL operation with less heat Recognized for 2500Vrms Main Features sinking required 11 0C rated junction Enable survivability Symbol Value Unit temperature of typically LED load I 12 A T(RMS) di/dt performance of operating characteristics V /V 600 V DRM RRM 70A/s Simplicity of circuit design I 10 mA GT QUADRAC version & layout includes intergrated DIAC UL 1557 as an Electrically Provides full control Isolated Semiconductor Schematic Symbol of light out put at the Device extreme low end of load conditions. MT1 MT2 G Additional Information Applications Excellent for AC switching and phase control applications such as heating, lighting, and motor speed controls. Typical applications are AC solid-state switches,lighting Datasheet Resources Samples controls with LED lamp loads, small low current motor in power tools, lower current motor in home/brown goods appliances. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.11/17/20Thyristors 12 Amp Alternistor (High Commutation) Triac for LED dimmer Application Absolute Maximum Ratings Symbol Parameter Value Unit Q6012LH1LED I RMS on-state current (full sine wave) T = 90C 12 A T(RMS) Q6012RH1LED C Q6012NH1LED f = 50 Hz t = 20 ms 110 Non repetitive surge peak on-state current I A TSM (full cycle, T initial = 25C) f = 60 Hz t = 16.7 ms 120 J 2 2 2 I t I t Value for fusing - t = 8.3 ms 60 A s p di/dt Critical rate of rise of on-state current f = 120 Hz T = 110C 70 A/s J t 10 s p I Peak gate trigger current T = 110C 2.0 A GTM J I I GT GTM P Average gate power dissipation - T = 110C 0.5 W G(AV) J T Storage temperature range - -40 to 150 C stg T Operating junction temperature range -40 to 110 C J Electrical Characteristics (T = 25C, unless otherwise specified) J Symbol Test Conditions Quadrant Value Unit I I II III MAX. 10 mA GT V = 12V R = 60 D L V I II III MAX. 1.3 V GT V V = V R = 3.3 k T = 110C I II III MIN. 0.2 V GD D DRM L J I I = 20mA MAX. 8 mA H T dv/dt V = V Gate Open T = 110C MIN. 45 V/s D DRM J (dv/dt)c (di/dt)c = 6.5 A/ms T = 110C MIN. 2 V/s J t I = 2 x I PW = 15s I = 17.0 A(pk) TYP. 4 s gt G GT T Static Characteristics Symbol Test Conditions Value Unit V I = 17.0A t = 380 s - MAX. 1.60 V TM TM p T = 25C 10 A I J DRM V = V / V MAX. D DRM RRM I RRM T = 110C 1 mA J Thermal Resistances Symbol Parameter Value Unit Q6012LH1LED 2.3 R Junction to case (AC) C/W Q6012RH1LED (J-C) 1.2 Q6012NH1LED 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BO.11/17/20