SE-601-0U-CC Littelfuse

Protection Relays and Controls Ungrounded DC System SE-601 SERIES (PGR-2601) DC Ground-Fault Monitor Description The SE-601 is a microprocessor-based ground-fault relay for ungrounded dc systems. It provides sensitive ground-fault protection without the problems associated with nuisance tripping. Ground-fault current is sensed using an SE-GRM Series Ground-Reference Modulea resistor network that limits ground-fault current to 25 mA. The SE-601 is used on ungrounded dc systems ranging from industrial 24-Vdc control circuits to 1000-Vdc solar and transportation systems. Features & Benefits FEATURES BENEFITS Adjustable pickup Ten settings provide a wide range of (1 - 20 mA) low-level protection Adjustable time delay Adjustable trip delay allows quick protection or (50 ms - 2.5 s) delayed response Form A and Form B output contacts for operation of Output contacts separate annunciation and trip circuits Analog output Provides means for connecting to a meter (0 - 5 V) (PGA-0500) or a control system Simplified Circuit Diagram Non-volatile trip Retains trip state when de-energized to simplify Memory troubleshooting + Selectable fail-safe or non-fail-safe operating Selectable contact modes allow connection to shunt or undervoltage A operating mode breaker coil SE-GRM SERIES UNGROUNDED Microprocessor based No calibration required saves on maintenance cost GROUND-REFERENCE SUPPLY MODULE Accessories - A SE-GRM Series Ground-Reference Module Required accessory, used to connect the SE-601 DC Ground-Fault Monitor to the SE-601 DC bus. (DC Ground-Fault Monitor) L1 PGA-0500 Analog % Current Meter L2 Optional panel-mounted analog meter displays ground-fault current as a percentage of 22 mA. Specifications Ordering Information IEEE Device Numbers DC Overcurrent Relay (76G) ORDERING NUMBER CONTROL POWER Input Voltage See ordering information SE-601-OU 120/240 Vac/Vdc Dimensions H 75 mm (3.0) W 55 mm (2.2) D 115 mm (4.5) Trip Level Settings 1-20 mA SE-601-OD 12/24 Vdc Trip Time Settings 0.05 -2.5 s SE-601-OT 48 Vdc Output Contacts Isolated Form A and Form B Contact Operating Mode Selectable fail-safe or non-fail-safe Test Button Local ACCESSORIES REQUIREMENT Reset Button Local and remote SE-GRM SERIES Required Analog Output 0-5 V PGA-0500 Optional Conformally Coated Consult factory Approvals CSA certified , UL Listed (E340889), PMA-55 Optional CE (European Union), C-Tick (Australian) PMA-60 Optional Warranty 5 years Mounting DIN, Surface (standard) Note: For optional conformal coating please consult factory. Panel (with PMA-55 or PMA-60 adapter) 2018 Littelfuse Protection Relays & Controls Rev: 4-C-050213 Littelfuse.com/se-601 Based on Manual Rev 2-A-041913X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Industrial Relays category: Click to view products by Littelfuse manufacturer: Other Similar products are found below : 6-1617801-8 6-1618107-9 7-1618273-3 EV250-4A-02 EV250-6A-01 FCA-125-CX8 FCA-325-159 FCA-410-138 8000-S3121 8-1618273-6 8-1618393-1 GCA63A220VAC60HZ GCA63A277VAC60HZ GCA63A600VAC60HZ 1-1672275-3 1-1833005-4 H-16/S1 A711Z ACC530U20 ACC633U30 ACC730U30 DH18DA 1423675-8 AVR907 15732A200 B07B032AC1-0329 B329 B490A 1618279-1 BHR124Y 1810DDB-SX N417 P30C42A12D1-120 2-1617748-6 2-1618396-6 2-1618398-1 JMGACD-5M JMGSC-5LW JMGSCD-5L PBO-18A1218 PBO-40A3040 K8DSPH1200480VAC KA-3C-12A RT334012WG S160156115 SAH159 2944795 301-17SX 1618105-2 1618112-6