698-501-63 Marl

PROFESSIONAL LED INDICATORS 8.1mm Mounting FEATURES 698 SERIES l Each product will operate over a wide voltage PACK QUANTITY = 10 PIECES input range l Black anodised aluminium housing l Full internal potting to resist shock and vibration l Sealed to IP67 l Fitted with an internal diode to provide reverse voltage protection to 1000Vdc SPECIFICATIONS Ordering Information & Typical Technical Characteristics (Ta = 25C) Mean Time Between Failure = 100,000 Hours. Luminous intensity figures refer to the unmodified discrete LED. PART NUMBER COLOUR LENS VOLTAGE CURRENT LUMINOUS WAVE OPERATING STORAGE DC (Vdc) DC (mA) INTENSITY LENGTH TEMP TEMP Vopr lopr lv 20mA (mcd) lp (nm) Topr Tstg HIGH INTENSITY 698-501-63 Red Smoked 12-28 8-20 11000 643 -40 ~ +95 -40 ~ +100 Yes 698-521-63 Yellow Smoked 12-28 8-20 16000 591 -40 ~ +95 -40 ~ +100 Yes 698-532-63 Green Smoked 12-28 8-20 23000 527 -40 ~ +95 -40 ~ +100 Yes 698-930-63 Blue Smoked 12-28 8-20 7000 470 -40 ~ +95 -40 ~ +100 Yes 698-997-63 Cool White Smoked 12-28 8-20 14000 *see below -40 ~ +95 -40 ~ +100 Yes 698-501-75 Red Smoked 110Vac 6 11000 643 -40 ~ +95 -40 ~ +100 Yes 698-521-75 Yellow Smoked 110Vac 6 16000 591 -40 ~ +95 -40 ~ +100 Yes 698-532-75 Green Smoked 110Vac 6 23000 527 -40 ~ +95 -40 ~ +100 Yes 698-930-75 Blue Smoked 110Vac 6 7000 470 -40 ~ +95 -40 ~ +100 Yes 698-997-75 Cool White Smoked 110Vac 6 14000 *see below -40 ~ +95 -40 ~ +100 Yes UNITS Vdc mA mcd nm C C = Products must be derated according to the derating information. Each derating graph refers to specific LEDs. Refer to page 3. 997F-C *Typical emission colour cool white Intensities (lv) and colour shades of white (x,y co-ordinates) may vary between LEDs within x 0.245 0.361 0.356 0.264 a batch. y 0.229 0.385 0.351 0.220 How to Order: website: www.marl.co.uk email: sales marl.co.uk Telephone +44 (0)1229 582430 Fax: +44 (0)1229 585155 The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation relating to either products or service. Marl International reserve the right to alter without notice the specification or any conditions of supply for products or service. Page 1 of 2 MARL INTERNATIONAL LTD 2007 : DS 063/07 Issue 1 SAMPLES AVAILABLE698 Series Mounting Hole Dimensions in mm (Typical) Anode termination indicated by red sleeve Not to scale Mounting hole to be clean and burr free MATERIALS PUSH-ON CONNECTORS Body Aluminium grade 6063 black anodised Nut Stainless Steel grade 303 Panel Seal Viton Termination Copper with silver flash finish Lock Washer Zinc plated steel Fresnel lens Polycarbonate Encapsulation PC5430 Dimensions in mm (Typical) 925-000-00 is brass tin plated. Header Nylon6 A82 Not to scale For use with 698 series lamps. TECHNICAL CHARACTERISTICS SERIES MAXIMUM PANEL NUT MINIMUM MIN/MAX. POWER CUTOUT MOUNTING MOUNTING PANEL DISSIPATION TORQUE CENTRES THICKNESS 698 825 8.1 0.65 x,y=14.5 1.5-13.0 mW mm Nm mm mm DERATING INFORMATION 501 & 521 532, 930 & 997 How to Order: website: www.marl.co.uk email: sales marl.co.uk Telephone +44 (0)1229 582430 Fax: +44 (0)1229 585155 The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation BS EN ISO 9001:2000 relating to either products or service. Marl International reserve the right to alter without notice the specification or any conditions of supply Approved Manufacturer for products or service. Page 2 of 2 MARL INTERNATIONAL LTD 2007 : DS 063/07 Issue 1 SAMPLES AVAILABLE