SP526 WAN Multi-Mode Serial Transceiver Low-Cost Programmable Serial Transceiver Four (4) Drivers and Four (4)) Receivers Driver and Receiver Tri-state Control Software Selectable Protocol Selection Interface Modes: ENR4 1 33 R3OUT RS-232 (V.28) ENR3 2 32 R4OUT ENR2 3 31 RS-422 (V.11, X.21) VCC ENR1 4 30 T4OUT EIA-530 or RS-449 (V.10, V.11) 5 29 T4IN T3OUTA Designed to Meet All NET1/2 Compliancy 6 28 T3IN SP526 T3OUTB 7 27 T2IN T2OUTA Requirements T1IN 8 26 T2OUTB High ESD Tolerance ENT4 9 25 T1OUTA 15kV per Human Body Model ENT3 10 24 T1OUTB ENT2 11 23 15kV per IEC1000-4-2 Air Discharge GND 8kV per IEC1000-4-2 Contact Discharge +5V 1.0F 1.0F 22 31 Now Available in Lead Free Packaging VCC VCC 21 20 C1+ VDD 1.0F 17 C1 15 VSS 19 SP526 1.0F C2+ 1.0F 16 DESCRIPTION C2 25 8 T1OUTA T1 24 T1IN The SP526 is a monolithic device that sup- T1OUTB 12 ENT1 ports three (3) physical layer serial interface 27 T2OUTA 7 T2 standards. The SP526 is fabricated using a T2IN 26 T2OUTB 11 low power BiCMOS process technology, and ENT2 29 T3OUTA 6 incorporates four (4) drivers and four (4) T3 T3IN 28 T3OUTB 10 receivers can be configured via software for ENT3 the selected interface modes at any time. 5 30 T4 T4IN T4OUT The SP526 includes tri-state ability for the 9 ENT4 driver and receiver outputs through separate 43 35 R1INA R1 42 R1OUT enable lines. A shutdown mode is also R1INB 4 ENR1 included through the mode select pins for 41 34 R2INA R2 40 R2OUT power savings. When mated with the SP322 R2INB 3 ENR2 V.11/V.35 Programmable Transceiver, the 39 33 R3INA R3 SP526 provides the four (4) channels needed 38 R3OUT R3INB 2 for handshaking/control lines such as CTS, ENR3 37 32 R4INA RTS, etc. The two transceiver ICs are an R4 36 R4OUT R4INB ideal solution for WAN serial ports in 1 14 ENR4 networking equipment such as routers, D0 13 DSU/CSU s, and other access devices. GND GND GND D1 44 18 23 Rev: C Date:2/1/06 SP526 MultiMode Serial Transceiver Copyright 2006 Sipex Corporation 1 12 44 ENT1 GND 13 D1 43 R1INA 14 42 R1INB D0 15 41 VSS R2INA 16 40 C2- R2INB 17 39 C1- R3INA 18 38 GND R3INB 19 37 C2+ R4INA 20 VDD 36 R4INB C1+ 21 35 R1OUT 22 34 VCC R2OUTABSOLUTE MAXIMUM RATINGS STORAGE CONSIDERATIONS These are stress ratings only and functional operation Due to the relatively large package size of the 44-pin of the device at these ratings or any other above those quad flat-pack, storage in a low humidity environment indicated in the operation sections of the specifications is preferred. Large high density plastic packages are below is not implied. Exposure to absolute maximum moisture sensitive and should be stored in Dry Vapor rating conditions for extended periods of time may Barrier Bags. Prior to usage, the parts should remain affect reliability. bagged and stored below 40C and 60%RH. If the V ............................................................................+7V parts are removed from the bag, they should be used CC Input Voltages: within 48 hours or stored in an environment at or below Logic...............................-0.3V to (V +0.5V) 20%RH. If the above conditions cannot be followed, CC Drivers............................-0.3V to (V +0.5V) the parts should be baked for four hours at 125C CC Receivers........................................15.5V in order remove moisture prior to soldering. Sipex ships Output Voltages: the 44-pin QFP in Dry Vapor Barrier Bags with Logic................................-0.3V to (V +0.5V) a humidity indicator card and desiccant pack. The CC Drivers................................................15V humidity indicator should be below 30%RH. Receivers........................-0.3V to (V +0.5V) CC Storage Temperature..........................-65C to +150C Power Dissipation (derate 14.3mW/C above 70C)................1144mW ELECTRICAL CHARACTERISTICS T = +25C and V = +4.75V to +5.25V unless otherwise noted. A CC PARAMETER MIN. TYP. MAX. UNITS CONDITIONS LOGIC INPUTS V 0.8 Volts IL V 2.0 Volts IH LOGIC OUTPUTS V 0.4 Volts I = 3.2mA OL OUT V 2.4 Volts I = 1.0mA OH OUT V.28 DRIVER DC Parameters Outputs Open Circuit Voltage 15 Volts per Figure 1 Loaded Voltage 5.0 15 Volts per Figure 2 Short-Circuit Current 100 mA per Figure 4 Power-Off Impedance 300 per Figure 5 AC Parameters V = +5V for AC parameters CC Outputs Transition Time 1.5 s per Figure 6 +3V to -3V Instantaneous Slew Rate 30 V/s per Figure 3 Propagation Delay t 0.5 1 5 s PHL t 0.5 1 5 s PLH Max.Transmission Rate 120 230 kbps V.28 RECEIVER DC Parameters Inputs Input Impedance 3 7 k per Figure 7 Open-Circuit Bias +2.0 Volts per Figure 8 HIGH Threshold 1.7 3.0 Volts LOW Threshold 0.8 1.2 Volts AC Parameters V = +5V for AC parameters CC Propagation Delay t 50 100 500 ns PHL t 50 100 500 ns PLH Rev: C Date:2/1/06 SP526 MultiMode Serial Transceiver Copyright 2006 Sipex Corporation - 2