XR19L202 TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER JULY 2007 REV. 1.0.1 APPLICATIONS GENERAL DESCRIPTION Battery-Powered Equipment The XR19L202 (L202) is a highly integrated device that combines a full-featured two channel Universal Handheld and Mobile Devices Asynchronous Receiver and Transmitter (UART) and RS- Handheld Terminals 232 transceivers. The L202 is designed to operate with a Industrial Peripheral Interfaces single 3.3V or 5V power supply. The L202 is fully compliant with EIA/TIA-232-F Standards from a +3.3V to +5.5V power Point-of-Sale (POS) Systems supply. The device operates at 1 Mbps data rate with worst FEATURES case 3K ohms load. Both RS-232 driver outputs and receiver inputs can operate in harsh electrical environments Meets true EIA/TIA-232-F Standards from +3.3V to +5.5V of +/-15V without damage and can survive multiple +/-15kV operation ESD on the RS-232 lines, while maintaining RS-232 output levels. Up to 1 Mbps data transmission rate The L202 operates in four different modes: Active, Partial 45us sleep mode exit (charge pump to full power) Sleep, Full Sleep and Power-Save. Each mode can be ESD protection for RS-232 I/O pins at invoked via hardware or software. Upon power-up, the +/-15kV - Human Body Model L202 is in the Active mode where the UART and RS-232 transceiver function normally. In the Partial Sleep mode, the +/-15kV - IEC 61000-4-2, Air-Gap Discharge internal crystal oscillator of the UART or charge pump of the +/- 8kV - IEC 61000-4-2, Contact Discharge RS-232 transceiver is turned off. In Full Sleep mode, both Software compatible with industry standard 16550 UART the crystal oscillator and the charge pump are turned off. Intel/Motorola bus select While the UART is in the Sleep mode, the Power-Save Complete modem interface mode isolates the core logic from the control signals (chip select, read/write strobes, address and data bus lines) to Sleep and Power-save modes to conserve battery power minimize the power consumption. The RS-232 receivers Wake-up interrupt upon exiting low power modes remain active in any of these four modes. FIGURE 1. BLOCK DIAGRAM VREF+ *5 V Tolerant Inputs Crystal PwrSave BRG Charge Pump Osc/Buffer A2:A0 VREF- 64 Byte TXA TXDA D7:D0 TX & RX RXA RXDA FIFO 5K IOR IOW (R/W ) Modem CSA (CS ) I/Os CSB INTA (IRQ ) Channel A Ch A Transceiver INTB RESET (RESET ) TXB TXDB Channel B Channel B TXB I/M Transceiver RXDB RXB RXB (See Figure 6) RXBSEL UART RS-232 Transceiver XR19L202 Exar Corporation 48720 Kato Road, Fremont CA, 94538 (510) 668-7000 FAX (510) 668-7017 www.exar.com Intel or Motorola Bus Interface UART Registers XTAL1 XTAL2 GND VCC (3.3 to 5.5V) R EN FAST ACP C2+ C2- C1+ C1-XR19L202 TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER REV. 1.0.1 FIGURE 2. PIN OUT OF THE DEVICE GND 1 36 C2P N.C. 2 35 RESET N.C. 3 C2N 34 D5 4 33 TXDA INTA D6 5 32 XR19L202 D7 6 31 INTB 48- pin QFN RXBSEL 7 30 A0 Intel Bus Mode RXB 8 29 A1 TXB 9 28 A2 CSA 10 27 RXDA CSB 26 11 GND PWRSAVE 12 25 RXDB VCC GND 1 36 C2P N.C. 2 35 RESET N.C. 3 C2N 34 D5 4 33 TXDA D6 5 32 IRQ XR19L202 D7 6 31 N.C. 48- pin QFN RXBSEL 7 30 A0 Motorola Bus Mode RXB 8 29 A1 TXB 9 28 A2 CS 27 RXDA 10 A3 26 11 GND PWRSAVE 12 25 RXDB GND ORDERING INFORMATION PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE DEVICE STATUS XR19L202IL48 48-pin QFN -40C to +85C Active 2 13 48 N.C. XTAL1 47 D4 XTAL2 14 FAST 15 46 D3 16 45 D2 IOW D1 17 44 GND 18 43 D0 IOR 42 C3 R EN 19 VCC 20 41 ACP 21 40 VREFP VREFN C1P 22 39 TXDB C1N 23 38 I/M 37 VCC N.C. 24 13 48 N.C. XTAL1 47 D4 XTAL2 14 FAST 15 46 D3 D2 16 45 R/W D1 17 44 GND 18 43 D0 N.C. 19 42 C3 R EN 41 VCC ACP 20 40 VREFP VREFN 21 C1P 22 39 TXDB 23 38 C1N I/M 24 37 VCC N.C.