XRA1405IL24-0B-EB MaxLinear

REV. 1.0.0 XRA1403/1405 EVALUATION BOARD USERS MANUAL INTRODUCTION This users manual is for the XRA1403/1405 16-bit evaluation board. Table 1 shows the different devices and packages that the evaluation board supports. This users manual will describe the hardware setup required to operate the different packages. 1.0 QUICK START To verify communication with the GPIO expander, the following steps are recommended: 1.1 Connect external +5V power supply to J8 pin 1 1.2 Connect J12 pin 13 and 14 to ground of external power supply 1.3 Connect to MCU SPI interface for: SPI clock (SCK SCL signal at J5 pin11) SO (SO SPI signal at J5 pin17) SI (SI SPI signal at J5 pin21) CS (CS SPI signal at J5 pin19) 1.4 From the MCU, write the following registers: GCR1 = 0x00 GCR2 = 0x00 If the LEDs turn on, the communication with the GPIO expander is successful. To disable connection to LEDs, remove jumpers on J28, J29, J30 and J31. Connect to external inputs or outputs at J3 and J4. 2.0 HARDWARE SETUP 2.1 Packages description The evaluation board supports all 4 packages of the XRA1403 and XRA1405. The ordering part number, package and location on the board is shown below in Table 1. Table 2 lists the evaluation board ordering part numbers. TABLE 1: PACKAGE LIST ORDERING PART NUMBER PACKAGE LOCATION XRA1403IL24-F 24-pin QFN U4 XRA1403IG24-F 24-pin TSSOP U5 XRA1405IL24-F 24-pin QFN U4 XRA1405IG24-F 24-pin TSSOP U5 TABLE 2: EVALUATION BOARD ORDERING PART NUMBERS PART NUMBER XRA1403IL24-0B-EB XRA1403IG24-0B-EB XRA1405IL24-0B-EB XRA1405IG24-0B-EB 1 XRA1403/1405 EVALUATION BOARD USERS MANUAL REV. 1.0.0 2.2 Jumper Settings 2.2.1 Common Jumpers The following jumpers apply to all the 4 packages of XRA1403 and XRA1405: TABLE 3: COMMON JUMPER SETTINGS JUMPERS FUNCTIONS COMMENTS J8 Selects the supply voltage to generate 1&2 selects +5V (default, Pin 1 -- Test point for external +5V) the +1.8V power supply for the board 2&3 selects +P NOTE: Not installed. Trace between 1 & 2 J9 Selects the supply voltage to generate 1&2 selects +5V (default) the +2.5V power supply for the board 2&3 selects +P NOTE: Not installed. Trace between 1 & 2 J13 Selects the supply voltage to generate 1&2 selects +5V (default) the +3.3V power supply for the board 2&3 selects +P NOTE: Not installed. Trace between 1 & 2 J10 Selects the supply voltage for +VDDP Used only for the XRA1405 Jumper in 1&2 selects +3.3V Jumper in 3&4 selects +2.5V Jumper in 5&6 selects +1.8V J11 Selects the supply voltage for +VDD Jumper in 1&2 selects +3.3V (default) Jumper in 3&4 selects +2.5V Jumper in 5&6 selects +1.8V J12 Not used for XRA140x Installed but not used J14 Not used for XRA140x Installed but not used J6 Not used Installed but not used NOTE: Not installed. Pin 2 is connected to GND J27 LEDs J3 Header for testing GPIO 15:8 of both Installed. Connect to external input/output. TSSOP and QFN package J4 Header for testing GPIO 7:0 of both Installed. Connect to external input/output. Remove jumpers on TSSOP and QFN package J28, J29, J30 and J31 after test. J2 Header for internal test Not installed J5 Header for XRA1403 and XRA1405 sig- Installed. Connect SPI signals from this header to MCU. nals and spare signals J7 Header for UART signals and spare sig- Not installed. Some GPIO signals and spare signals are accessi- nals ble at this header 2