8332 Fast Set Epoxy 8332 is a quick-set 2-part epoxy adhesive. Bonded parts need only be held together for eight to ten minutes before handling. It offers excellent adhesion to a wide range of materials that are difcfi ult to bond with, including glass, bfi erglass, concrete, ceramics, woods, and most metals and plastics. This is a general-purpose adhesive suitable for household, industrial and manufacturing applications. Cured Properties Features & Benefits Breakdown Voltage 23 200 V Quick set time Dielectric Strength 250 V/mil Low shrinkage 14 Resistivity 1.7 x 10 cm Provides strong electrical insulation Hardness 82 D Protects against thermal and mechanical 2 Tensile Strength 34 N/mm shocks 2 Compressive Strength 63 N/mm 2 Strong resistance to humidity, salt water, Lap Shear (stainless steel) 4.9 N/mm 2 acids, bases, and aliphatic hydrocarbons (aluminum) 5.9 N/mm Comes in convenient dual cartridges, suitable Glass Transition Temperature (T ) 64 C g for automated dispensing applications CTE Prior T 76 ppm/C g CTE After T 175 ppm/C g Service Temperature Range -40150 C Available Packaging Usage Parameters Cat. No. Packaging Net Vol. Net Wt. Working Time 3 to 5 min 8332-25ML Dual Syringe 25 mL 28.6 g Set Time 8 to 10 min 8332-50ML Dual Cartridge 46 mL 79.3 g Functional Cure 22 C 5 h Mix Ratio by Volume 1:1 Mix Ratio by Weight 1:1 Contact Information MG Chemicals, 1210 Corporate Drive Uncured Properties Burlington, Ontario, Canada L7L 5R6 Mixed Density 1.14 g/mL Email: support mgchemicals.com Viscosity 25 C (A) 12 Pas Phone: Nor th America: +(1)80 0 -3 40 - 0772 (B) 14 Pas Shelf Life 3 y International: +(1) 905-331-1396 Europe: +(44)1663 362888 ISO 9001:2015 Quality Management System. Burlington, Ontario, Canada SAI Global File: 004008 17 May 2021 / Ver. 3.1 18332 Application Instructions Dispensing Accessories Read the product SDS and Application Guide for Consult the table below for accessory selection. See more detailed instructions before using this product the Dispensing Accessories Application Guide for (downloadable at www.mgchemicals.com). usage instructions. 8MT-50-FT should only be used with a pneumatic dispenser. Recommended Preparation Cat. No. Dispensing Gun Static Mixer Clean the substrate with Isopropyl Alcohol, MG 824, so the surface is free of oils, dust, and other residues. 8332-25ML N/A 8MT-25 8332-50ML 8DG-50-1-1 8MT-50 Syringe or Cartridge 1. Twist and remove the cap from the cartridge or Cure Instructions syringe. Do not discard cap. Allow to cure at room temperature for 5 hours, or cure 2. Dispense a small amount to ensure even flow of the adhesive in an oven for 15 min at 65 C. both parts. 3. (Optional) Attach a static mixer. Storage and Handling a. Dispense and discard 3 to 5 mL of the product to Store between 16 and 27 C in a dry area, away from ensure a homogeneous mixture. sunlight (see SDS). To maximize shelf life, recap b. After use, dispose of static mixer. product firmly when not in use. 4. Without a static mixer, dispense material on a mixing surface or container, and thoroughly mix parts A and B together. 5. To stop the flow, pull back on the plunger. 6. Clean nozzle to prevent contamination and material buildup. 7. Replace the cap on the cartridge or syringe. Disclaimer This information is believed to be accurate. It is intended for professional end-users who have the skills required to evaluate and use the data properly. M.G. Chemicals Ltd. does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it. ISO 9001:2015 Quality Management System. Burlington, Ontario, Canada SAI Global File: 004008 17 May 2021 / Ver. 3.1 2