WWW.Microsemi .COM 1N5221 1N5281B, e3 DO-7 1N5221 thru 1N5281,e3 DO-7 500 mW GLASS AXIAL-LEAD ZENER DIODES SCOTTSDALE DIVISION DESCRIPTION APPEARANCE The popular 1N5221 thru 1N5281B series of 0.5 watt Zener Voltage DO-7 Regulators provides a selection from 2.4 to 200 volts in standard 5% or 10% (DO-204AA) tolerances as well as tighter tolerances identified by different suffix letters on the part number. These glass axial-leaded DO-7 Zeners are also available in various military screening levels by adding a prefix identifier as described in the Features section. Microsemi also offers numerous other Zener products to meet higher and lower power applications. IMPORTANT: For the most current data, consult MICROSEMIs website: WWW.Microsemi .COM 1N5221 1N5281B, e3 DO-7 1N5221 thru 1N5281,e3 DO-7 500 mW GLASS AXIAL-LEAD ZENER DIODES SCOTTSDALE DIVISION Max Zener Impedance Max Reverse Leakage Current Max Zener Nominal A & B Suffix Only Voltage Temp. Test A, B, C & D Suffix Only Non-Suffix JEDEC Zener Note 2 Coeff. Current Type No. Voltage I V (A & B Suffix R R I Z I = 0.25 I V Used ZT ZK ZK R R Note 1 V I Z I Only) Z ZT ZT ZK A Volts mA mA For Suffix A o Volts Ohms (% / C) VZ Ohms A A B,C & D Note 3 1N5231 5.1 20 17 1600 5.0 1.9 2.0 50 +/-0.030 1N5232 5.6 20 11 1600 5.0 2.9 3.0 50 +0.038 1N5233 6.0 20 7.0 1600 5.0 3.3 3.5 50 +0.038 1N5234 6.2 20 7.0 1000 5.0 3.8 4.0 50 +0.045 1N5235 6.8 20 5.0 750 3.0 4.8 5.0 30 +0.050 1N5236 7.5 20 6.0 500 3.0 5.7 6.0 30 +0.058 1N5237 8.2 20 8.0 500 3.0 6.2 6.5 30 +0.062 1N5238 8.7 20 8.0 600 3.0 6.2 6.5 30 +0.065 1N5239 9.1 20 10 600 3.0 6.7 7.0 30 +0.068 1N5240 10 20 17 600 3.0 7.6 8.0 30 +0.075 1N5241 11 20 22 600 2.0 8.0 8.4 30 +0.076 1N5242 12 20 30 600 1.0 8.7 9.1 10 +0.077 1N5243 13 9.5 13 600 0.5 9.4 9.9 10 +0.079 1N5244 14 9.0 15 600 0.1 9.5 10 10 +0.082 1N5245 15 8.5 16 600 0.1 10.5 11 10 +0.082 1N5246 16 7.8 17 600 0.1 11.4 12 10 +0.083 1N5247 17 7.4 19 600 0.1 12.4 13 10 +0.084 1N5248 18 7.0 21 600 0.1 13.3 14 10 +0.085 1N5249 19 6.6 23 600 0.1 13.3 14 10 +0.086 1N5250 20 6.2 25 600 0.1 14.3 15 10 +0.086 1N5251 22 5.6 29 600 0.1 16.2 17 10 +0.087 1N5252 24 5.2 33 600 0.1 17.1 18 10 +0.088 1N5253 25 5.0 35 600 0.1 18.1 19 10 +0.089 1N5254 27 4.6 41 600 0.1 20 21 10 +0.090 1N5255 28 4.5 44 600 0.1 20 21 10 +0.091 1N5256 30 4.2 49 600 0.1 22 23 10 +0.091 1N5257 33 3.8 58 700 0.1 24 25 10 +0.092 1N5258 36 3.4 70 700 0.1 26 27 10 +0.093 1N5259 39 3.2 80 800 0.1 29 30 10 +0.094 1N5260 43 3.0 93 900 0.1 31 33 10 +0.095 1N5261 47 2.7 105 1000 0.1 34 36 10 +0.095 1N5262 51 2.5 125 1100 0.1 37 39 10 +0.096 1N5263 56 2.2 150 1300 0.1 41 43 10 +0.096 1N5264 60 2.1 170 1400 0.1 44 46 10 +0.097 1N5265 62 2.0 185 1400 0.1 45 47 10 +0.097 1N5266 68 1.8 230 1600 0.1 49 52 10 +0.097 1N5267 75 1.7 270 1700 0.1 53 56 10 +0.098 1N5268 82 1.5 330 2000 0.1 59 62 10 +0.098 1N5269 87 1.4 370 2200 0.1 65 68 10 +0.099 1N5270 91 1.4 400 2300 0.1 66 69 10 +0.099 1N5271 100 1.3 500 2600 0.1 72 76 10 +0.110 1N5272 110 1.1 750 3000 0.1 80 84 10 +0.110 1N5273 120 1.0 900 4000 0.1 86 91 10 +0.110 1N5274 130 0.95 1100 4500 0.1 94 99 10 +0.110 1N5275 140 0.90 1300 4500 0.1 101 106 10 +0.110 1N5276 150 0.85 1500 5000 0.1 108 114 10 +0.110 1N5277 160 0.80 1700 5500 0.1 116 122 10 +0.110 1N5278 170 0.74 1900 5500 0.1 123 129 10 +0.110 1N5279 180 0.68 2200 6000 0.1 130 137 10 +0.110 1N5280 190 0.66 2400 6500 0.1 137 144 10 +0.110 1N5281 200 0.65 2500 7000 0.1 144 152 10 +0.110 *JEDEC registered data. JEDEC type numbers listed indicate a tolerance of +/-20% with guaranteed limits on only V , I , and V . Devices with Z R F guaranteed limits on all six parameters are indicated by suffix A for +/-10% tolerance and suffix B for +/-5% tolerance. Also available with suffix C or D which indicates 2% and 1% tolerance respectively. NOTES: 1. The electrical characteristics are measured after allowing the device to stabilize for 20 seconds when mounted with a 3/8 (10 mm) minimum lead length from the case. 2. The zener impedance is derived from the 60 Hz ac voltage that results when an ac current having an rms value equal to 10% of the dc zener current (I or I ) is superimposed on I or I . Zener impedance is measured at two points to ensure a sharp knee on the breakdown curve, ZT ZK ZT ZK thereby eliminating unstable units. Also see MicroNote 202 for variation in dynamic impedance with different operating currents. 3. Temperature coefficient ( ). Test conditions for temperature coefficient are as follows: VZ o o a. I = 7.5 mA, T = 25 C, T = 125 C (1N5221A, B thru 1N5242A, B). ZT 1 2 o o b. I = Rated I , T = 25 C, T = 125 C (1N5243A, B thru 1N5281A, B). ZT ZT 1 2 (Device to be temperature stabilized with current applied prior to reading breakdown voltage at the specified ambient temp.) Copyright 2005 Microsemi Page 2 8-29-2005 REV B Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503