24AA02H/24LC02BH 2 2K I C Serial EEPROM with Half-Array Write-Protect Device Selection Table Description: Part VCC Max. Clock Temp. The Microchip Technology Inc. 24AA02H/24LC02BH Number Range Frequency Ranges (24XX02H*) is a 2 Kbit Electrically Erasable PROM. (1) The device is organized as one block of 256 x 8-bit 24AA02H 1.7-5.5 400 kHz I memory with a 2-wire serial interface. Low-voltage 24LC02BH 2.5-5.5 400 kHz I, E design permits operation down to 1.7V, with standby Note 1: 100 kHz for VCC <2.5V and active currents of only 1 A and 1 mA, respec- tively. The 24XX02H also has a page write capability for up to 8 bytes of data. The 24XX02H is available in the Features: standard 8-pin PDIP, surface mount SOIC, TSSOP, 2x3 Single Supply with Operation down to 1.7V for TDFN and MSOP packages, and is also available in 24AA02H Devices, 2.5V for 24LC02BH Devices the 5-lead SOT-23 and SC-70 packages. Low-Power CMOS Technology: - Read current 1 mA, max. Package Types - Standby current 1 A, max. (I-temp) SOIC, TSSOP PDIP, MSOP 2 2-Wire Serial Interface, I C Compatible A0 1 8 VCC A0 1 8 VCC Schmitt Trigger Inputs for Noise Suppression A1 2 7 WP 2 7 A1 WP Output Slope Control to Eliminate Ground Bounce A2 3 6 SCL 3 6 100 kHz and 400 kHz Clock Compatibility A2 SCL Page Write Time 3 ms, typical 4 5 VSS 4 5 SDA VSS SDA Self-Timed Erase/Write Cycle SOT-23/SC-70 TDFN 8-Byte Page Write Buffer Hardware Write-Protect for Half-Array (80h-FFh) A0 1 VCC 8 WP SCL15 ESD Protection >4,000V 7 WP A1 2 6 SCL Vss 2 A2 3 More than 1 Million Erase/Write Cycles VSS 4 5 SDA Data Retention >200 Years 3 4 Vcc SDA Factory Programming Available Packages include 8-lead PDIP, SOIC, TSSOP, Note: Pins A0, A1 and A2 are not used by the 24XX02H (no internal connections). TDFN, MSOP, 5-lead SOT-23 and SC-70 Pb-Free and RoHS Compliant Block Diagram Temperature Ranges: - Industrial (I): -40C to +85C HV WP Generator - Automotive (E): -40C to +125C I/O Memory EEPROM Control Control XDEC Array Logic Logic Page Latches I/O SCL YDEC SDA VCC Sense Amp. VSS R/W Control 2008 Microchip Technology Inc. DS22105A-page 124AA02H/24LC02BH 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins ............................................................... ....................................................................................... 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS Electrical Characteristics: DC CHARACTERISTICS Industrial (I): VCC = +1.7V to 5.5V TA = -40C to +85C Automotive (E): VCC = +2.5V to 5.5V TA = -40C to +125C Param. Sym. Characteristic Min. Max. Units Conditions No. D1 A0, A1, A2, SCL, SDA and WP pins: D2 VIH High-level input voltage 0.7 VCC V D3 VIL Low-level input voltage 0.3 VCC V D4 VHYS Hysteresis of Schmitt 0.05 VCC V (Note) Trigger inputs (SDA, SCL pins) D5 VOL Low-level output voltage 0.40 V IOL = 3.0 ma VCC = 4.5V IOL = 2.1 ma VCC = 2.5V D6 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS D7 ILO Output leakage current 1 AVOUT = VSS or VCC D8 CIN, Pin capacitance 10 pFVCC = 5.0V (Note) COUT (all inputs/outputs) TA = 25C, f = 1 MHz D9 ICC Read Operating current 1 mA VCC = 5.5V, SCL = 400 kHz ICC Write 3 mA VCC = 5.5V D10 ICCS Standby current 1 AVCC = 5.5V, SCL = SDA = VCC WP = VSS, A0, A1, A2 = VSS Note: This parameter is periodically sampled and not 100% tested. DS22105A-page 2 2008 Microchip Technology Inc.