24LC21T-ISN Microchip

24LC21 24LC21 Not recommended for new designs Please use 24LCS21A. 24LC21 2 1K 2.5V Dual Mode I C Serial EEPROM Features: Package Types Single supply with operation down to 2.5V PDIP Completely implements DDC1 /DDC2 interface NC 1 8 VCC for monitor identification Low-power CMOS technology: NC 2 7 VCLK - 1 mA active current typical -10 A standby current typical at 5.5V NC 3 6 SCL 2 2-wire serial interface bus, I C compatible VSS 4 5 SDA Self-timed write cycle (including auto-erase) Page-write buffer for up to 8 bytes 100 kHz (2.5V) and 400 kHz (5V) compatibility SOIC Factory programming (QTP) available 1,000,000 erase/write cycles ensured 1 8 Data retention > 200 years NC VCC 8-pin PDIP and SOIC package 2 7 NC VCLK Available for extended temperature ranges Commercial (C): 0C to +70C 3 5 NC SCL Industrial (I): -40C to +85C 4 5 VSS SDA Description: The Microchip Technology Inc. 24LC21 is a 128 x 8 bit Electrically Erasable PROM. This device is designed for use in applications requiring storage and serial transmission of configuration and control information. Block Diagram Two modes of operation have been implemented: Transmit-only mode and Bidirectional mode. Upon VCLK power-up, the device will be in the Transmit-only mode, HV Generator sending a serial bit stream of the entire memory array contents, clocked by the VCLK pin. A valid high-to-low transition on the SCL pin will cause the device to enter I/O Memory EEPROM Control Control the Bidirectional mode, with byte selectable read/write Array XDEC Logic Logic capability of the memory array. The 24LC21 is available Page Latches in a standard 8-pin PDIP and SOIC package, in both commercial and industrial temperature ranges. SDA SCL YDEC VCC Sense Amp VSS R/W Control 2 I C is a trademark of Philips Corporation. DDC is a trademark of the Video Electronics Standards Association. 2004 Microchip Technology Inc. DS21095J-page 124LC21 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................7.0V All inputs and outputs w.r.t. VSS ........................................................................................................ -0.6V to VCC + 1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C Soldering temperature of leads (10 seconds) .......................................................................................................+300C ESD protection on all pins ...................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS VCC = +2.5V to 5.5V DC CHARACTERISTICS Commercial (C): TA = 0C to +70C Industrial (I): TA = -40C to +85C Parameter Symbol Min Max Units Conditions SCL and SDA pins: VIH .7 VCC V High-level input voltage VIL .3 VCC V Low-level input voltage Input levels on VCLK pin: VIH 2.0 .8 V VCC 2.7V (Note 1) High-level input voltage VIL .2 VCC V VCC < 2.7V (Note 1) Low-level input voltage Hysteresis of Schmitt Trigger inputs VHYS .05 VCC V (Note 1) Low-level output voltage VOL1 .4 V IOL = 3 mA, VCC = 2.5V (Note 1) Low-level output voltage VOL2 .6 V IOL = 6 mA, VCC = 2.5V Input leakage current ILI -10 10 AVIN = .1V to VCC Output leakage current ILO -10 10 AVOUT = .1V to VCC Pin capacitance (all inputs/outputs) CIN, COUT 10 pF VCC = 5.0V (Note1), TA = 25C, FCLK = 1 MHz Operating current ICC Write 3 mA VCC = 5.5V, SCL = 400 kHz ICC Read 1 mA Standby current ICCS 30 A VCC = 3.0V, SDA = SCL = VCC 100 A VCC = 5.5V, SDA = SCL = VCC (Note 2) Note 1: This parameter is periodically sampled and not 100% tested. 2: VLCK must be grounded. DS21095J-page 2 2004 Microchip Technology Inc.