24LC515T-I/SM Microchip

24AA515/ 24AA515/ 24AA515/24LC515/24FC515 2 512K I C CMOS Serial EEPROM Device Selection Table Package Type PDIP Part VCC Max Clock Temp A0 1 8 VCC Number Range Frequency Ranges A1 2 7 WP 24AA515 1.8-5.5V 400 kHz I 24LC515 2.5-5.5V 400 kHz I A2 3 6 SCL 24FC515 2.5-5.5V 1 MHz I VSS 4 5 SDA 100 kHz for VCC < 2.5V. Features SOIC Low-power CMOS technology 1 8 A0 VCC - Maximum write current 3 mA at 5.5V 2 7 A1 WP - Maximum read current 400 A at 5.5V 3 6 - Standby current 100 nA typical at 5.5V A2 SCL 2 2-wire serial interface bus, I C compatible 4 5 VSS SDA Cascadable for up to four devices Self-timed ERASE/WRITE cycle 64-byte Page Write mode available 5 ms max write cycle time Block Diagram Hardware write-protect for entire array A0 A1 WP HV Generator Output slope control to eliminate ground bounce Schmitt Trigger inputs for noise suppression 100,000 erase/write cycles I/O Memory EEPROM Electrostatic discharge protection > 4000V Control Control XDEC Array Logic Logic Data retention > 200 years Page Latches 8-pin PDIP, SOIC packages Temperature ranges: I/O SCL - Industrial (I): -40Cto +85C YDEC SDA Description The Microchip Technology Inc. 24AA515/24LC515/ VCC 24FC515 (24XX515*) is a 64K x 8 (512K bit) Serial Sense AMP VSS R/W Control Electrically Erasable PROM, capable of operation across a broad voltage range (1.8V to 5.5V). It has been developed for advanced, low power applications such as personal communications or data acquisition. This device has both byte write and page write capabil- ity of up to 64 bytes of data. This device is capable of both random and sequential reads. Reads may be sequential within address boundaries 0000h to 7FFFh & 8000h to FFFFh. Functional address lines allow up to four devices on the same data bus. This allows for up to 2 Mbits total system EEPROM memory. This device is available in the standard 8-pin plastic DIP and SOIC 24XX515 is used in this document as a generic part number packages. for the 24AA515/24LC515/24FC515 devices. 2003 Microchip Technology Inc. Preliminary DS21673C-page 124AA515/24LC515/24FC515 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-65C to +125C ESD protection on all pins ...................................................................................................................................................... 4kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS DC CHARACTERISTICS Industrial (I): VCC = +1.8V to 5.5V TA = -40C to +85C Param. Sym Characteristic Min Max Units Conditions No. D1 A0, A1, SCL, SDA, and WP pins: D2 VIH High-level input voltage 0.7 VCC VVCC 2.5V D3 VIL Low-level input voltage 0.3 VCC V VCC 2.5V 0.2 VCC V VCC < 2.5V D4 VHYS Hysteresis of Schmitt 0.05 VCC VVCC 2.5V (Note) Trigger inputs (SDA, SCL pins) D5 VOL Low-level output voltage 0.40 V IOL = 3.0 mA VCC = 4.5V IOL = 2.1 mA VCC = 2.5V D6 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS VIN = VSS or VCC, WP = VCC D7 ILO Output leakage current 1 AVOUT = VSS or VCC D8 CIN, Pin capacitance 10 pFVCC = 5.0V (Note) COUT (all inputs/outputs) TA = 25C, fC= 1 MHz D9 ICC Read Operating current 400 AVCC = 5.5V, SCL = 400 kHz ICC Write 3 mA VCC = 5.5V D10 Iccs Standby current 5 A SCL = SDA = VCC = 5.5V A0, A1, WP = VSS, A2 = VCC Note: This parameter is periodically sampled and not 100% tested. DS21673C-page 2 Preliminary 2003 Microchip Technology Inc.