24VL024/24VL025 2 2K I C Serial EEPROM Device Selection Table Description: The Microchip Technology Inc. 24VL024/24VL025 is a Part Number VCC Range Max Clock 2Kbit Serial Electrically Erasable PROM with (1) 24VL024 1.5 to 3.6V 400 kHz operation down to 1.5V. The device is organized as a single block of 256 x 8-bit memory with a 2-wire serial (1) 24VL025 1.5 to 3.6V 400 kHz interface. Low-current design permits operation with maximum standby and active currents of only 1 A and Note 1: 100 kHz for VCC < 1.8V 400 A, respectively. The device has a page write capability for up to 16 bytes of data. Functional address Features: lines allow the connection of up to eight 24VL024/ 24VL025 devices on the same bus for up to 16 Kbits of Single-Supply with Operation down to 1.5V contiguous EEPROM memory. The device is Low-Power CMOS Technology: available in the standard 8-pin PDIP, 8-pin SOIC (150 - 400 A active current, maximum mil), TSSOP, 2x3 TDFN and MSOP packages. The -1 A standby current, maximum 24VL025 is also available in the 6-lead, SOT-23 2 2-Wire Serial Interface Bus, I C Compatible package. Schmitt Trigger Inputs for Noise Suppression Block Diagram Output Slope Control to Eliminate Ground Bounce WP A0 A1 A2 100 kHz and 400 kHz Compatibility HV Generator Page Write Buffer for up to 16 Bytes Self-Timed Write Cycle (including Auto-Erase) I/O Memory Control Hardware Write Protection for the Entire Array Control EEPROM Logic XDEC (24VL024 only) Logic Array Cascadable up to Eight Devices More than 1 Million Erase/Write Cycles SDA SCL ESD Protection > 4,000V Write-Protect Circuitry Data Retention > 200 Years VCC YDEC Factory Programming (QTP) Available VSS 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP Sense Amp. Packages R/W Control 6-lead SOT-23 package (24VL025 only) Temperature Range: Package Types - -20C to +85C SOIC, TSSOP PDIP, MSOP Pb-Free and RoHS Compliant A0 1 8 VCC 1 8 A0 VCC A1 2 7 WP A1 2 7 WP A2 3 6 SCL 3 6 A2 SCL VSS 4 5 SDA SS 4 5 V SDA SOT-23 TDFN SCL 6 VCC A0 1 8 VCC 1 WP 2 7 A1 VSS 2 5 A0 6 SCL A2 3 SDA 4 A1 3 VSS 4 5 SDA (24VL025 only) Note: WP pin is not internally connected on the 24VL025 2009 Microchip Technology Inc. DS22130A-page 124VL024/24VL025 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied..................................................................................................-20C to +85C ESD protection on all pins .................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS Electrical Characteristics: DC CHARACTERISTICS VCC = +1.5V to 3.6V TA = -20C to +85C Param. Sym. Characteristic Min. Max. Units Conditions No. D1 A0, A1, A2, SCL, SDA and WP pins: D2 VIH High-level input voltage 0.7 VCC V D3 VIL Low-level input voltage 0.3 VCC V D4 VHYS Hysteresis of Schmitt 0.05 VCC V (Note) Trigger inputs (SDA, SCL pins) D5 VOL Low-level output voltage 0.40 V IOL = 3.0 mA VCC = 3.6V IOL = 2.1 mA VCC = 2.5V D6 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS D7 ILO Output leakage current 1 AVOUT = VSS or VCC D8 CIN, Pin capacitance 10 pFVCC = 3.6V (Note) COUT (all inputs/outputs) TA = 25C, f = 1 MHz D9 ICC Read Operating current 400 AVCC = 3.6V, SCL = 400 kHz ICC Write 3 mA VCC = 3.6V D10 ICCS Standby current 1 AVCC = 3.6V, SCL = SDA = VCC WP = VSS, A0, A1, A2 = VSS Note: This parameter is periodically sampled and not 100% tested. DS22130A-page 2 2009 Microchip Technology Inc.