MCP112-195ITO Microchip

MCP111/112 Micropower Voltage Detector Features Package Types Ultra-low supply current: 1.75 A (max.) 3-Pin SOT23-3/SC-70 3-Pin SOT-89 Precision monitoring options of: V DD - 1.90V, 2.32V, 2.63V, 2.90V, 2.93V, 3.08V, V 1 OUT 4.38V and 4.63V Resets microcontroller in a power-loss event V 3 MCP111/112 DD Active-low V pin: OUT - MCP111 active-low, open-drain V 1 2 3 2 SS - MCP112 active-low, push-pull V V V OUT DD SS Available in SOT23-3, TO-92, SC-70 and 3-Pin TO-92 SOT-89-3 packages Temperature Range: - Extended: -40C to +125C (except MCP1XX-195) - Industrial: -40C to +85C (MCP1XX-195 only) V OUT V V SS DD Pb-free devices Applications Block Diagram Critical Microcontroller and Microprocessor Power-Monitoring Applications V DD Computers Intelligent Instruments Comparator Portable Battery-Powered Equipment V + OUT Output Description Driver The MCP111/112 are voltage-detecting devices designed to keep a microcontroller in reset until the Band Gap system voltage has stabilized at the appropriate level Reference for reliable system operation. These devices also operate as protection from brown-out conditions when the system supply voltage drops below the specified V SS threshold voltage level. Eight different trip voltages are available. TABLE 1: DEVICE FEATURES Output Reset Delay Package Pin Out Device Comment (typ) (Pin 1, 2, 3) Type Pull-up Resistor MCP111 Open-drain External No V , V , V OUT SS DD MCP112 Push-pull No No V , V , V OUT SS DD MCP102 Push-pull No 120 ms RST, V , V See MCP102/103/121/131 Data Sheet DD SS (DS21906) MCP103 Push-pull No 120 ms VSS, RST, V See MCP102/103/121/131 Data Sheet DD (DS21906) MCP121 Open-drain External 120 ms RST, V , V See MCP102/103/121/131 Data Sheet DD SS (DS21906) MCP131 Open-Drain Internal (~95 k ) 120 ms RST, V , V See MCP102/103/121/131 Data Sheet DD SS (DS21906) 2004-2013 Microchip Technology Inc. DS21889E-page 1 MCP111/112MCP111/112 Notice: Stresses above those listed under Maximum 1.0 ELECTRICAL Ratings may cause permanent damage to the device. This is CHARACTERISTICS a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Absolute Maximum Ratings Exposure to maximum rating conditions for extended periods V . 7.0V may affect device reliability. DD Input current (V ) 10 mA DD Output current (RST) 10 mA Rated Rise Time of V 100V/s DD All inputs and outputs (except RST) w.r.t. V SS .-0.6V to (V + 1.0V) DD RST output w.r.t. V . -0.6V to 13.5V SS Storage temperature .65C to + 150C Ambient temp. with power applied . -40C to + 125C Maximum Junction temp. with power applied 150C ESD protection on all pins 2kV DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all limits are specified for V = 1V to 5.5V, R = 100 k (only MCP111), DD PU T = -40C to +125C. A Parameters Sym Min Typ Max Units Conditions Operating Voltage Range V 1.0 5.5 V DD Specified V Value to V low V 1.0 V I = 10 A, V < 0.2V DD OUT DD RST RST Operating Current I < 1 1.75 A DD V Trip Point MCP1XX-195 V 1.872 1.900 1.929 V T = +25C (Note 1) DD TRIP A 1.853 1.900 1.948 V T = -40C to +85C (Note 2) A MCP1XX-240 2.285 2.320 2.355 V T = +25C (Note 1) A 2.262 2.320 2.378 V Note 2 MCP1XX-270 2.591 2.630 2.670 V T = +25C (Note 1) A 2.564 2.630 2.696 V Note 2 MCP1XX-290 2.857 2.900 2.944 V T = +25C (Note 1) A 2.828 2.900 2.973 V Note 2 MCP1XX-300 2.886 2.930 2.974 V T = +25C (Note 1) A 2.857 2.930 3.003 V Note 2 MCP1XX-315 3.034 3.080 3.126 V T = +25C (Note 1) A 3.003 3.080 3.157 V Note 2 MCP1XX-450 4.314 4.380 4.446 V T = +25C (Note 1) A 4.271 4.380 4.490 V Note 2 MCP1XX-475 4.561 4.630 4.700 V T = +25C (Note 1) A 4.514 4.630 4.746 V Note 2 V Trip Point Tempco T 100 ppm/ DD TPCO C Note 1: Trip point is 1.5% from typical value. 2: Trip point is 2.5% from typical value. 3: This specification allows this device to be used in PIC microcontroller applications that require the In-Circuit Serial Programming (ICSP) feature (see device-specific programming specifications for voltage requirements). This specification DOES NOT allow a continuous high voltage to be present on the open-drain output pin (V ). The total OUT time that the V pin can be above the maximum device operational voltage (5.5V) is 100 sec. Current into the V OUT OUT pin should be limited to 2 mA. It is recommended that the device operational temperature be maintained between 0C to 70C (+25C preferred). For additional information, please refer to Figure 2-28. 4: This parameter is established by characterization and is not 100% tested. DS21889E-page 2 2004-2013 Microchip Technology Inc.