MCP37211-200 MCP37D11-200 200 Msps, 12-Bit Low-Power ADC with 8-Channel MUX Digital Signal Post-Processing (DSPP) Options: Features - Decimation filters for improved SNR Sample Rates: - Fractional Delay Recovery (FDR) for time- - 200 Msps for single-channel mode delay corrections in multi-channel operations - 200 Msps/number of channels used (dual-/octal-channel modes) SNR with f = 15 MHz and -1 dBFS: IN - Noise-Shaping Requantizer (NSR) - 71.3 dBFS (typical) at 200 Msps - Phase, Offset and Gain adjust of individual SFDR with f = 15 MHz and -1 dBFS: IN channels - 90 dBc (typical) at 200 Msps - Digital Down-Conversion (DDC) with I/Q or Power Dissipation with LVDS Digital I/O: f /8 output (MCP37D11-200) S - 468 mW at 200 Msps - Continuous wave beamforming for octal- Power Dissipation with CMOS Digital I/O: channel mode (MCP37D11-200) - 436 mW at 200 Msps, Output Clock = 100 MHz Serial Peripheral Interface (SPI) Power Dissipation Excluding Digital I/O: AutoSync Mode to Synchronize Multiple Devices - 387 mW at 200 Msps to the Same Clock Power-Saving Modes: AEC-Q100 Qualified (Automotive Applications) - 144 mW during Standby Package Options: - 28 mW during Shutdown (a) TFBGA-121 (8 mm x 8 mm x 1.08 mm): Supply Voltage: - AEC-Q100 qualified - Digital Section: 1.2V, 1.8V - Temperature Grade 1: -40C to +125C - Analog Section: 1.2V, 1.8V - Includes embedded decoupling capacitors for Selectable Full-Scale Input Range: up to 2.975 V P-P reference pins and bandgap output pin Input Channel Bandwidth: 500 MHz (b) VTLA-124 (9 mm x 9 mm x 0.9 mm) Channel-to-Channel Crosstalk in Multi-Channel - Temperature Range: -40C to +85C Mode (Input = 15 MHz, -1 dBFS): >95 dB Output Data Format: Typical Applications - Parallel CMOS, DDR LVDS Communication Instruments Optional Output Data Randomizer Microwave Digital Radio Built-In ADC Linearity Calibration Algorithms: Cellular Base Stations - Harmonic Distortion Correction (HDC) Lidar and Radar - DAC Noise Cancellation (DNC) Ultrasound and Sonar Imaging - Dynamic Element Matching (DEM) Low-Power High-Speed Instruments - Flash Error Calibration (1) MCP372X1/MCP37DX1-200 Family Comparison Digital Digital CW Noise-Shaping Part Number Sample Rate Resolution (2) (3) (4) (2) Decimation Down-Conversion Beamforming Requantizer MCP37231-200 200 Msps 16 Yes No No No MCP37221-200 200 Msps 14 Yes No No No MCP37211-200 200 Msps 12 Yes No No Yes MCP37D31-200 200 Msps 16 Yes Yes Yes No MCP37D21-200 200 Msps 14 Yes Yes Yes No MCP37D11-200 200 Msps 12 Yes Yes Yes Yes Note 1: Devices in the same package type are pin-to-pin compatible. 2: Available in single- and dual-channel modes. 3: Available in single- and dual-channel modes, and octal-channel mode when CW beamforming is enabled. 4: Available in octal-channel mode. 2014-2019 Microchip Technology Inc. DS20005355D-page 1MCP37211-200 AND MCP37D11-200 Functional Block Diagram AV AV GND DV DV DD12 DD18 DD12 DD18 Duty Cycle DLL CLK+ Clock Correction Selection CLK- PLL DCLK+ Output Clock Control DCLK- A + IN0 Digital Signal Post-Processing: A - IN0 Pipelined - FDR, Decimation ADC - Phase/Offset/Gain Adj. 1 - DDC, CW Beamforming A + IN7 Note 1: Only available in MCP37D11-200. A - IN7 WCK V V REF+ REF- OVR Output Control: V CM - CMOS, DDR LVDS - Serialized LVDS Reference Q 11:0 SENSE Generator Internal Registers V BG SLAVE REF1+ REF1- REF0- SDIO SCLK CS SYNC REF0+ DS20005355D-page 2 2014-2019 Microchip Technology Inc. Input Multiplexer