MCP604T-I/ST Microchip

MCP601/1R/2/3/4 2.7V to 6.0V Single Supply CMOS Op Amps Features Description Single-Supply: 2.7V to 6.0V The Microchip Technology Inc. MCP601/1R/2/3/4 family of low-power operational amplifiers (op amps) Rail-to-Rail Output are offered in single (MCP601), single with Chip Select Input Range Includes Ground (CS) (MCP603), dual (MCP602), and quad (MCP604) Gain Bandwidth Product: 2.8 MHz (typical) configurations. These op amps utilize an advanced Unity-Gain Stable CMOS technology that provides low bias current, high- Low Quiescent Current: 230 A/amplifier (typical) speed operation, high open-loop gain, and rail-to-rail output swing. This product offering operates with a Chip Select (CS): MCP603 only single supply voltage that can be as low as 2.7V, while Temperature Ranges: drawing 230A (typical) of quiescent current per - Industrial: -40C to +85C amplifier. In addition, the common mode input voltage - Extended: -40C to +125C range goes 0.3V below ground, making these Available in Single, Dual, and Quad amplifiers ideal for single-supply operation. These devices are appropriate for low power, battery Typical Applications operated circuits due to the low quiescent current, for A/D convert driver amplifiers because of their wide Portable Equipment bandwidth or for anti-aliasing filters by virtue of their low A/D Converter Driver input bias current. Photo Diode Pre-amp The MCP601, MCP602, and MCP603 are available in Analog Filters standard 8-lead PDIP, SOIC, and TSSOP packages. Data Acquisition The MCP601 and MCP601R are also available in a Notebooks and PDAs standard 5-lead SOT-23 package, while the MCP603 is Sensor Interface available in a standard 6-lead SOT-23 package. The MCP604 is offered in standard 14-lead PDIP, SOIC, and TSSOP packages. Available Tools The MCP601/1R/2/3/4 family is available in the SPICE Macro Models Industrial and Extended temperature ranges and has a Software FilterLab power supply range of 2.7V to 6.0V. Mindi Simulation Tool MAPS (Microchip Advanced Part Selector) Analog Demonstration and Evaluation Boards Application Notes Package Types MCP601 MCP604 MCP602 MCP603 PDIP, SOIC, TSSOP PDIP, SOIC, TSSOP PDIP, SOIC, TSSOP PDIP, SOIC, TSSOP NC V NC V V 1 8 NC 1 V 1 OUTA 8 1 8 CS OUTA 14 OUTD DD V V 2 7 V 2 V V 2 V V 2 13 DD 7 7 V IN INA OUTB IN DD INA IND V + V + V + V + 3 6 V 3 6 V 3 3 12 V + IN INA 6 V INA OUT INB IN IND OUT V V V V SS 4 5 4 5 4 4 11 V NC SS V + SS 5 DD NC SS INB V + 5 10 INB V + INC MCP601 MCP601R MCP603 V 6 9 V INB INC SOT23-5 SOT23-5 SOT23-6 V 7 8 OUTB V V V V OUTC 1 5 V 1 5 V 1 6 V OUT OUT OUT DD SS DD V 2 V 2 V 2 5 CS SS DD SS V + V + V + 3 4 V 3 4 V 3 4 V IN IN IN IN IN IN 2007 Microchip Technology Inc. DS21314G-page 1MCP601/1R/2/3/4 Notice: Stresses above those listed under Absolute 1.0 ELECTRICAL Maximum Ratings may cause permanent damage to the CHARACTERISTICS device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not Absolute Maximum Ratings implied. Exposure to maximum rating conditions for extended V V ........................................................................7.0V periods may affect device reliability. DD SS Current at Input Pins .....................................................2 mA See Section 4.1.2 Input Voltage and Current Limits. Analog Inputs (V +, V ) ........ V 1.0VtoV +1.0V IN IN SS DD All Other Inputs and Outputs ......... V 0.3V to V +0.3V SS DD Difference Input Voltage ...................................... V V DD SS Output Short Circuit Current .................................Continuous Current at Output and Supply Pins ............................30 mA Storage Temperature....................................65C to +150C Maximum Junction Temperature (T )..........................+150C J ESD Protection On All Pins (HBM MM) .............. 3 kV 200V DC CHARACTERISTICS Electrical Specifications: Unless otherwise specified, T = +25C, V = +2.7V to +5.5V, V = GND, V = V /2, A DD SS CM DD V V /2, V = V /2, and R = 100 k to V , and CS is tied low. (Refer to Figure 1-2 and Figure 1-3). OUT DD L DD L L Parameters Sym Min Typ Max Units Conditions Input Offset Input Offset Voltage V -2 0.7 +2 mV OS Industrial Temperature V -3 1 +3 mV T = -40C to +85C (Note 1) OS A Extended Temperature V -4.5 1 +4.5 mV T = -40C to +125C (Note 1) OS A Input Offset Temperature Drift V /T 2.5 V/CT = -40C to +125C OS A A Power Supply Rejection PSRR 80 88 dB V = 2.7V to 5.5V DD Input Current and Impedance Input Bias Current I 1 pA B Industrial Temperature I 20 60 pAT = +85C (Note 1) B A Extended Temperature I 450 5000 pA T = +125C (Note 1) B A Input Offset Current I 1 pA OS 13 Common Mode Input Impedance Z pF CM 10 6 13 Differential Input Impedance Z pF DIFF 10 3 Common Mode Common Mode Input Range V V 0.3 V 1.2 V CMR SS DD Common Mode Rejection Ratio CMRR 75 90 dB V = 5.0V, V = -0.3V to 3.8V DD CM Open-loop Gain DC Open-loop Gain (large signal) A 100 115 dB R = 25 k to V , OL L L V = 0.1V to V 0.1V OUT DD A 95 110 dB R = 5 k to V , OL L L V = 0.1V to V 0.1V OUT DD Output Maximum Output Voltage Swing V , V V + 15 V 20 mV R = 25 k to V , Output overdrive = 0.5V OL OH SS DD L L V , V V + 45 V 60 mV R = 5 k to V , Output overdrive = 0.5V OL OH SS DD L L Linear Output Voltage Swing V V + 100 V 100 mV R = 25 k to V , A 100 dB OUT SS DD L L OL V V + 100 V 100 mV R = 5 k to V , A 95 dB OUT SS DD L L OL Output Short Circuit Current I 22 mAV = 5.5V SC DD I 12 mAV = 2.7V SC DD Power Supply Supply Voltage V 2.7 6.0 V (Note 2) DD Quiescent Current per Amplifier I 230 325 A I = 0 Q O Note 1: These specifications are not tested in either the SOT-23 or TSSOP packages with date codes older than YYWW = 0408. In these cases, the minimum and maximum values are by design and characterization only. 2: All parts with date codes November 2007 and later have been screened to ensure operation at V =6.0V. However, the DD other minimum and maximum specifications are measured at 1.4V and/or 5.5V. DS21314G-page 2 2007 Microchip Technology Inc.