MIC94305YMT-TR Microchip

MIC94300 200mA Switch with Ripple Blocker Technology General Description Features The MIC94300 is an integrated load switch that 1.8V to 3.6V input voltage range incorporates Micrels Ripple Blocker active filter Active noise rejection over a wide frequency band technology. The MIC94300 provides high-frequency ripple >60dB from 40kHz to 5MHz attenuation (switching noise rejection) for applications Rated to 200mA output current where a switching noise cannot be tolerated by sensitive Current-limit and thermal-limit protected downstream circuits such as in RF applications. A low- voltage logic enable pin disconnects the pass element and Ultra-small 0.88mm x 0.88mm 4-ball CSP places the MIC94300 into a low current-shutdown state 1.2mm x 1.6mm, 4-pin Thin MLF when disabled. Logic-controlled enable pin The MIC94300 operates from an input voltage of 1.8V to 40C to +125 C junction temperature range 3.6V, allowing true load switching of low-voltage power rails in any electronic device. The output voltage (V ) is OUT set at a fixed drop (typically 170mV) from the input voltage Applications (V = V 170mV). This maintains high efficiency OUT IN Smart phones independent of given load conditions and currents. Tablet PC/notebooks and webcams Packaged in a 0.88mm x 0.88mm 4-ball CSP or 4-pin 1.2mm x 1.6mm Thin MLF package, the MIC94300 has a Digital still and video cameras junction operating temperature range of 40 C to +125 C. Videoconferencing Data sheets and support documentation can be found on Bar-code scanners Micrels web site at: www.micrel.com. Global positioning systems Automotive and industrial applications Typical Application PSRR C = 1F OUT 0 -10 -20 -30 V = 3.6V IN -40 -50 V = 1.8V IN -60 -70 V = 2.5V IN -80 V = V + 40mVpp IN IN(NOM) -90 LOAD = 100mA -100 10 100 1K 10K 100K 1M 10M 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 1.E+06 1.E+07 FREQUENCY (Hz) Ripple Blocker is a trademark of Micrel, Inc MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc. Micrel Inc. 2180 Fortune Drive San Jose, CA 95131 USA tel +1 (408) 944-0800 fax + 1 (408) 474-1000 Micrel, Inc. MIC94300 Ordering Information Part Number Marking Code Package Lead Finish MIC94300YCS AF Pb-Free 0.88mm 0.88mm WLCSP 1,2 MIC94300YMT 43Z Pb-Free 1.2mm 1.6mm Thin MLF Notes: 1. Thin MLF = Pin 1 identifier. 2. Thin MLF is a GREEN RoHS-compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. Pin Configuration Top View Top View 4-Ball 0.88mm 0.88mm CSP (CS) 4-Pin 1.2mm 1.6mm Thin MLF (MT) Pin Description Pin Number Ball Number Pin Name Pin Name (Thin MLF ) (CSP) Enable input. A logic HIGH signal on this pin enables the part. Logic LOW 1 B2 EN disables the output. Do not leave floating. 2 B1 GND Ground. 3 A1 VOUT Power switch output. 4 A2 VIN Power switch input and chip supply. EP ePad Exposed Heatsink Pad. Connect to Ground for best thermal performance. M9999-020312-A February 2012 2