TC1188RECTTR Microchip

TC1188/TC1189 MAX8863/64 Pin Compatible, Low Dropout, 120 mA Linear Regulators Features General Description Input Voltage Range: 2.7 V to 6.0 V The TC1188 and TC1189 are fixed output, low dropout linear regulators that operate from a 2.7V to 6.0V input 120 mA Output Current voltage source. The output is capable of delivering up Low Supply Current: 50 A, (typical) to 120 mA while consuming only 50 A of quiescent Low Dropout Voltage: 110 mV, (typical at 100 mA) current. The low dropout voltage, 120 mV, make the Fast Turn-On from Shutdown: 140 sec (typical) TC1188 and TC1189 good choices for battery powered Low Output Noise applications. Integrated over-current and over-temper- Over-Current and Over-Temperature Protection ature protection features provide for a fault tolerant solution. Low Power Shutdown Mode The TC1189 includes an output voltage auto discharge Auto Discharge of Output Capacitor (TC1189) feature. When shutdown, the TC1189 will automatically Applications discharge the output voltage using an internal N-Chan- nel MOSFET switch. Battery Powered Systems Fixed output voltage options for the TC1188/TC1189 Portable Computers are: 1.80V, 2.80V, 2.84V and 3.15V. Both the TC1188 Medical Instruments and TC1189 are available in SOT23-5 packages. Cellular, Cordless Phones PDAs Typical Application Circuit Pagers Output V V IN OUT Voltage Package Type TC1188 5-Pin SOT-23A TC1189 + C C GND V OUT IN OUT 1F SHDN 1F 5 4 Battery TC1188 GND GND TC1189 1 3 2 SHDN GND V IN NOTE: 5-Pin SOT-23A is equivalent to the EIAJ (SC-74A) 2002-2012 Microchip Technology Inc. DS21364C-page 1TC1188/TC1189 *Notice: *Stresses above those listed underAbsolute 1.0 ELECTRICAL Maximum Rating may cause permanent damage to CHARACTERISTICS the device. These are stress ratings only and functional operation of the device at these or any other conditions Absolute Maximum Ratings* above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Input Voltage .........................................................6.5V Maximum Rating conditions for extended periods may Output Short-Circuit Duration.............................Infinite affect device reliability. Output Voltage........................... (-0.3V) to (V + 0.3V) IN Maximum Voltage On Any Pin.... (-0.3V) to (V +0.3V) IN Continuous Power Dissipation (T = +70C) A SOT-23-5 (derate 7.1 mW/C above +70C) ..................................................................571 mW Operating Temperature Range...............-40C to 85C Storage Temperature..........................-65C to +160C Lead Temperature (Soldering, 10 Sec.) ........... +300C DC SPECIFICATIONS Electrical Characteristics: V = +3.6V, GND = 0V, T = T to T , unless otherwise noted. Typical values are at T = +25C. IN A MIN MAX A (Note 1) Parameters Symbol Min Typ Max Units Conditions Input Voltage V V +0.5V 6.0 VV 2.5V IN OUT OUT 2.7 6.0 V = 1.8V (Note 2) OUT Output Voltage V 3.05 3.15 3.25 V 0 mA I 50 mA T OUT OUT 2.75 2.84 2.93 V 0 mA I 50 mA S OUT 2.70 2.80 2.88 V 0 mA I 50 mA R OUT 1.745 1.80 1.85 V 0 mA I 50 mA Q OUT Maximum Output Current I 120 mA OUT Current Limit I 280 mA Note 3 LIM Input Current I 50 90 AI = 0 IN OUT Dropout Voltage 1.1 mV I = 1 mA OUT 55 120 mV I = 50 mA OUT 110 240 mV I = 100 mA (Note 4) OUT Line Regulation V -0.10 0.001 0.10 %/V V = V 0.5V to 6.0V LNR IN OUT %/VI = 1 mA OUT Load Regulation V 0.01 0.040 %/mA I = 0 mA to 50 mA LDR OUT Output Voltage Noise 350 V 10 Hz to 1 MHz, C = 1 F RMS OUT 220 V 10 Hz to 1 MHz C = 100 F RMS OUT Wake Up Time t 10 secV = 3.6V WK IN C = 1 F, C = 1 F IN OUT (from Shutdown Mode) I = 30 mA, (See Figure 3-1) L Setting Time t 140 sec V = 3.6V S IN C = 1 F, C = 1 F IN OUT (from Shutdown Mode) I = 30 mA, (See Figure 3-1) L Note 1: Limits are 100% production tested at T = +25C. Limits over the operating temperature range are ensured through cor- A relation using Statistical Quality Control (SQC) methods. 2: Validated by line regulation test. 3: Not tested. For design purposes, the current limit should be considered 150 mA minimum to 410 mA maximum. 4: The dropout voltage is defined as (V V ) when V is 100 mV below the value of V for IN OUT OUT OUT V = V +2V. IN OUT DS21364C-page 2 2002-2012 Microchip Technology Inc.