DL4746A-TP Micro Commercial Components (MCC)

NOT RECOMMENDED FOR NEW DESIGNS USE SMAJ4733A-TP~SMAJ4761A-TP DL4728A M C C Micro Commercial Components TM THRU 20736 Marilla Street Chatsworth Micro Commercial Components CA 91311 DL4761A Phone: (818) 701-4933 Fax: (818) 701-4933 Features 1 Watt x High Reliability x Very Sharp Reverse Characteristic Zener Diode x Low Reverse Current Level 3.3 to 75 Volts Lead Free Finish/RoHS Compliant(Note 1) Suffix designates RoHS Compliant. See ordering information) Moisture Sensitivity Level 1 GLASS MELF Maximum Ratings x Operating Temperature: -65 t o +175 x Storage Temperature: -65 to +175 Cathode Mark x 1 Watt DC Power Dissipation x Maximum Thermal Resistance: 100K/W Junction To Ambient Test Conditions: I = 9.5mm(3/8),T = constant L x Maximum Forward Voltage 200mA: 1.2 Volts C Figure 1 - Typical Temperature Coefficient B A 40 mV/ 20 INCHES MM DIM MIN MAX MIN MAX NOTE A .190 .205 4.80 5.20 0 B --- .022 --- .55 Nominal 0 20 40 C .095 .105 2.40 2.67 V Z Typical Temperature Coefficient (mV/ ) versus Zener Voltage (V ) Z SUGGESTED SOLDER Figure 2 - Derating Curve PAD LAYOUT .210 1.0 W .115 0.5 .035 25 100 150 200 Temperature Power Dissipation (W) - Versus - Temperature Notes: 1. Lead in Glass Exemption Applied, see EU Directive Annex Notes 7(C)-I w w w mme s c c i mo c . Revision: C 2012/08/23 1 of 3M C C TM Micro Commercial Components DL4728A thru DL4761A ELECTRICAL CHARACTERISTICS 25C MCC ZENER TEST MAXIMUM MAXIMUM TEST MAXIMUM MAXIMUM TEST MAXIMUM PART VOLTAGE CURRENT DYNAMIC REVERSE VOLTAGE REGULATOR KNEE CURRENT SURGE NUMBER V I IMPEDANCE CURRENT V CURRENT IMPEDANCE I CURRENT Z ZT R ZK Z I I V IZM Z I I ZT ZT R R ZK ZK S TA = 50C VOLTS mA OHMS A VOLTS mA OHMS mA mA DL4728A 3 . 3 76 10 100 1 276 400 1 . 0 1280 DL4729A 3 . 6 69 10 100 1 252 400 1 . 0 1260 DL4730A 3 . 9 64 9 50 1 234 400 1 . 0 1190 DL4731A 4. 3 58 9 10 1 217 400 1 . 0 1070 DL4732A 4 . 7 53 8 10 1 193 500 1 . 0 970 DL4733A 5 . 1 49 7 10 1 178 550 1 . 0 890 DL4734A 5 . 6 45 5 10 2 162 600 1 . 0 810 DL4735A 6 . 2 41 2 10 3 146 700 1 . 0 730 DL4736A 6 . 8 37 3 . 5 10 4 133 700 1 . 0 660 DL4737A 7 . 5 34 4 . 0 10 5 121 700 0 . 5 605 DL4738A 8 . 2 31 4 . 5 10 6 110 700 0 . 5 550 DL4739A 9 . 1 28 5 . 0 10 7 100 700 0 . 5 500 DL4740A 10 25 7 10 7 . 6 91 700 0.25 454 DL4741A 11 23 8 5 8 . 4 83 700 0.25 414 DL4742A 12 21 9 5 9 . 1 76 700 0.25 380 DL4743A 13 19 10 5 9 . 9 69 700 0.25 344 DL4744A 15 17 14 5 1 1 . 4 61 700 0.25 304 DL4745A 16 1 5 . 5 16 5 1 2 . 2 57 700 0.25 285 DL4746A 18 14 20 5 1 3 . 7 50 750 0.25 250 DL4747A 20 1 2 . 5 22 5 1 5 . 2 45 750 0.25 225 DL4748A 22 1 1 . 5 23 5 1 6 . 7 41 750 0.25 205 DL4749A 24 1 0 . 5 25 5 1 8 . 2 38 750 0.25 190 DL4750A 27 9 . 5 35 5 2 0 . 6 34 750 0.25 170 DL4751A 30 8 . 5 40 5 2 2 . 8 30 1000 0.25 150 DL4752A 33 7 . 5 45 5 2 5 . 1 27 1000 0.25 135 DL4753A 36 7 . 0 50 5 2 7 . 4 25 1000 0.25 125 DL4754A 39 6 . 5 60 5 2 9 . 7 23 1000 0.25 115 DL4755A 43 6 . 0 70 5 3 2 . 7 22 1500 0.25 110 DL4756A 47 5 . 5 80 5 3 5 . 8 19 1500 0.25 95 DL4757A 51 5 . 0 95 5 3 8 . 8 18 1500 0.25 90 DL4758A 56 4 . 5 110 5 4 2 . 6 16 2000 0.25 80 DL4759A 62 4 . 0 125 5 4 7 . 1 14 2000 0.25 70 DL4760A 68 3 . 7 150 5 5 1 . 7 13 2000 0.25 65 DL4761A 75 3 . 3 175 5 5 6 . 0 12 2000 0.25 60 NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage. Suffix A signifies 5% tolerance, C signifies 2% tolerance. NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to 10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure a sharp knee on the breakdown curve and eliminate unstable units. o NOTE 3 The reverse surge current is measured at 25 C ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second duration superimposed on Izt NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current w w w mme s c c i mo c . 2 of 3 Revision: C 2012/08/23