REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED D Add device type 02. 01-10-24 Raymond Monnin E Added a class E device for cage 50434. Updated paragraphs 3.1 and 02-05-01 Raymond Monnin 4.2. Added paragraph 4.3.6 in section 4 for listing the class E exceptions. Added the class E part numbers in the Standard Microcircuit Drawing Bulletin page. -sld F Add device type 03. 03-08-22 Raymond Monnin G Table I For the Input-output insulation current test (I ), under the 04-09-16 Raymond Monnin I-O condition block changedRH 45 toRH 65 . Editorial changes throughout. -sld H Table I Changed the symbols in the conditions block for the Output 04-12-09 Raymond Monnin withstand voltage, Output on resistance, Output leakage current, Input forward voltage, Turn-on time, and Turn-off time tests. Editorial changes throughout. -sld J Added footnote to paragraph 1.2.2. Re-worded paragraph 4.3.6 for 05-08-09 Raymond Monnin clarification of the class E requirements -sld. K 12-03-09 Charles F. Saffle Updated drawing paragraphs. -sld L 15-12-01 Charles F. Saffle Added device type 04. -sld M 17-08-03 Charles F. Saffle Figure 1: Corrected dimensions D and S for case outlines X and Y. Editorial changes throughout. -sld REV M SHEET 15 REV STATUS REV M M M M M M M M M M M M M M OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 STANDARD CHECKED BY 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 93140 01 H P A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices meet the MIL-PRF-38534 specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 1/ Generic number Circuit function 01 HSSR-7111, HSSR-711E, 53111-1 Power switch with optically isolated control 02 HSSR-7112, 53111-2 Power switch with optically isolated control 03 53111-3 Power switch with optically isolated control 04 53115-4 Power switch with optically isolated control 1.2.3 Device class designator. This device class designator is a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1/ See paragraph 4.3.6 herein for class E device(s). SIZE STANDARD 5962-93140 A MICROCIRCUIT DRAWING DLA LAND AND MARITIME REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 M 2 DSCC FORM 2234 APR 97