MIKROE-1714 MikroElektronika

2. Soldering the headers Before using your click board, make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 4. Essential features GPS3 click 2 3 The L80 module aboard GPS3 click incor- porates several technologies that enhance 1. Introduction the GPS performance. EASY Technology ensures that L80 can calculate and predict orbits automatically using data stored in its internal flash memory. AlwaysLocate tech- nology adaptively adjusts the on/off time to balance between positioning accuracy Turn the board upside down so that Turn the board upward again. Make sure and power consumption. The Automatic the bottom side is facing you upwards. to align the headers so that they are antenna switching function enables Place shorter pins of the header into the perpendicular to the board, then solder switching between the internal patch anten- appropriate soldering pads. the pins carefully. na and the external active antenna, keeping positioning during the switching process. GPS3 click carries Quectels L80, a high-sensitivity ultra slim GPS module 3. Plugging the board in with a patch antenna. With it, you can add click GPS functionality to your design without Once you have soldered the headers your the need for an external antenna (although board is ready to be placed into the desired BOARD the click board has a connector for one mikroBUS socket. Make sure to align the www.mikroe.com should you require it). An onboard red LED cut in the lower-right part of the board with will blink to indicate successful satellite the markings on the silkscreen at the GPS3 click manual acquisition. GPS3 click communicates mikroBUS socket. If all the pins ver. 1.00 with the target board through mikroBUS are aligned correctly, push the UART (RX, TX) and RST lines. The board is board all the way into the socket. 0 100000 027318 designed to use a 3.3V power supply. 5. GPS3 click board schematic 6. External antenna connector GPS3 click has a con- nector for an external active antenna that could be used along- side, or instead of the VCC VCC patch antenna thats already on the module. To get one, search for R1 R4 3K3 2K2 GPS antenna at www.mikroe.com/store LD1 LD2 Q1 R2 BC846 7. Code examples 1K Once you have done all the necessary R3 100K preparations, its time to get your click board VCC J1 1 VCC-BCKP up and running. We have provided examples (unsolder jumper when GND 2 backup battery is used) GND GND for mikroC , mikroBasic and mikroPascal M1 compilers on our Libstock website. Just TIMER 1PPS 7 6 External V BCKP NC antenna download them and you are ready to start. 8 5 AN PWM CN2 connection NC RST INT VCC 9 4 QuectelQuectel CS TX P 3 CN1 RESET GND SIGNAL 10 3 SCK RX L80L80 VCC Backup SCL EX ANT TXD1 C1 E1 C2 E2 P 1 MISO 11 2 GND battery SDA 100nF 10uF 100nF 4.7uF P 2 MOSI GND RXD1 GND 12 1 connection +3.3V +5V pads GND GND .com L80 GPS GND MIKROBUS DEVICE CONN. GND GND GND GND GND GND GND 8. Support MikroElektronika oers ff free tech support (www.mikroe.com/support) until the end of the products lifetime, so if something goes wrong, were ready and willing to help MikroElektronika assumes no responsibility or liability for any errors or inaccuracies that may appear in the present document. Specification and information contained in the present schematic are subject to change at any time without notice. Copyright 2014 MikroElektronika. All rights reserved.