MIKROE-1898 MikroElektronika

2. Soldering the headers Before using your click board , make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 PWM click 2 3 4. Essential features PWM click can be used to control anything from a LED strip, set of servo motors, to a complex robot with a multitude of moving parts. The board has an additional set of pins that allow you to connect up to seven Turn the board upside down so that Turn the board upward again. Make sure PWM clicks together (using three jumpers 2 the bottom side is facing you upwards. to align the headers so that they are to specify a different I C address for each Place shorter pins of the header into the perpendicular to the board, then solder the one). This way, you can get a total of 112 2 appropriate soldering pads. pins carefully. PWM outputs on a single I C line 1. Introduction 3. Plugging the board in click PWM click is a simple solution for con- Once you have soldered the headers your trolling 16 PWM outputs through a single board is ready to be placed into the desired 2 BOARD I C interface. The click board carries the mikroBUS socket. Make sure to align the www.mikroe.com PCA9685PW IC. In addition to mikroBUS cut in the lower-right part of the board with 2 I C pins (SCL, SDA), the board also uses a the markings on the silkscreen at the LOW Output Enable Input pin (OE), which is mikroBUS socket. If all the PWM click manual ver 1.01 in place of the default mikroBUS RST pin. pins are aligned correctly, PWM click is designed to use either a 3.3V or push the board all the way 5V power supply. into the socket. 01000000785638. Code examples 5. Schematic Once you have done all the necessary preparations, its time to get your click board VDD VDD CH0 CH1 up and running. We have provided examples CH2 CH3 CH4 CH5 for mikroC , mikroBasic and mikroPascal J2 A0 CH6 CH7 C1 compilers on our Libstock website. Just 100nF CN1 VDD J3 A1 VDD download them and you are ready to start. GND GND U1 CH8 CH9 J4 A2 CH10 CH11 1 28 A0 A0 VDD CH12 CH13 A1 2 27 SDA CH14 CH15 A1 SDA .com A2 3 26 SCL GND A2 SCL CN2 4 25 VDD A3 EXTCLK GND 5 24 VDD A4 A5 6 23 CH0 OE VDD CH0 OE J1 SDA CH1 7 22 CH15 CH1 CH15 SCL 9. Support CH2 8 21 CH14 OE CH2 CH14 9 20 CH3 CH13 VDD VDD CH3 CH13 VDD CN4 CH4 10 19 CH12 CH4 CH12 AN PWM CH5 11 18 CH11 OE R2 R1 R4 MikroElektronika offers free tech support CH5 CH11 EN INT GND 4K7 4K7 2K2 CH6 12 17 CH10 CS TX CH6 CH10 (www.mikroe.com/support) until the end of SCK RX CH7 13 16 CH9 SCL VDD CH7 CH9 MISO SCL SDA 14 15 the products lifetime, so if something goes CH8 MOSI SDA VSS CH8 LED +3.3V +5V R3 SDA GND GND wrong, were ready and willing to help SCL 4K7 MIKROBUS DEVICE CONN. OE GND CN3 GND GND GND GND GND 6. Dimensions 7. SMD jumper 10. Disclaimer MikroElektronika assumes no responsibility mm mils or liability for any errors or inaccuracies that may appear in the present document. LENGTH 57.15 2250 Specification and information contained in WIDTH 25.4 1000 the present schematic are subject to change HEIGHT* 3.5 138 at any time without notice. PWM click has a PWR SEL jumper (zero ohm 57.15 / 2250 mils * without headers resistor) that lets you switch the board form Copyright 2015 MikroElektronika. 3.3V to 5V power supply. All rights reserved. PCA9685PW/Q900 25.4 mm / 1000 mils