111040-3304 Molex

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 M M LABEL TEXT 18.35 0.10 (2X) L L ORIENTATION P1 P2 SEE DETAIL 1 K K LENGTH (SEE TABLE) LABEL TEXT 8.5 0.1 (2X) ORIENTATION J J 50 10 50 10 H H LABEL TEXT 16.4 0.1 (2X) (PCB WIDTH) ORIENTATION SEE SHEET 3 FOR LABEL DETAIL (FOR CABLES UNDER 2 METERS LABEL ON ONE END ONLY) G G 30 AWG ASSEMBLY 11.6 REF F F 28 AWG ASSEMBLY 13.0 REF E E 26-24 AWG ASSEMBLY PCB VIEWING HOLES 13.8 REF D D DETAIL1 SCALE 4:1 SEE SHEET 3 FOR P/N TABLE C C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE CURRENT REV DESC: OBSOLETED PART NO NOTES: mm 2:1 1. CABLE DISTANCE DEPENDS ON WIRE GAUGE, DATA RATE, AND GENERAL TOLERANCES (UNLESS SPECIFIED) HOST BOARD DRIVER CAPABILITIES EC NO: 611198 QSFP+ COPPER PATCH CABLE ASSEMBLY ANGULAR TOL 0.5 2. MATERIALS: CABLE ASSEMBLY DRWN: AKUMAR19 2018/12/31 4 PLACES BACKSHELLS - ZINC DIE CAST WITH BRIGHT NICKEL PLATING CHK D: GGA 2019/02/28 B B DELATCH - STAINLESS STEEL WITH OVERMOLDED NYLON 3 PLACES APPR: GGA 2019/02/28 PRODUCT CUSTOMER DRAWING PCB - FR4 2 PLACES 0.13 INITIAL REVISION: DOCUMENT NUMBER DOC TYPE DOC PART REVISION RIVETS - STAINLESS STEEL 1 PLACE 0.25 DRWN: SCHANNARAYAN 2017/08/22 PSD 000 3. IMPEDANCE - 100 OHMS DIFFERENTIAL 1110400001 Y 0 PLACES APPR: ARAYBURN 2017/09/06 MATERIAL NUMBER 4. RoHS COMPLIANT, NO EXEMPTIONS THIRD ANGLE PROJECTION DRAWING SERIES CUSTOMER SHEET NUMBER DRAFT WHERE APPLICABLE MUST REMAIN A A SEE P/N TABLE GENERAL MARKET 1 OF 3 D-SIZE 111040 DOCUMENT STATUS P1 RELEASE DATE 2019/02/28 12:46:47 WITHIN DIMENSIONS FORMAT: master-tb-prod-D REVISION: H 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 DATE: 2018/01/18 LABEL TEXT ORIENTATION LABEL TEXT ORIENTATION LABEL TEXT ORIENTATION20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 M M LEGEND: WIRING DIAGRAM ---- = THRU LINES P1 END P2 END ---> = TRANSMIT TO RECEIVE ON HIGH SPEED CIRCUITS PAD PAD SIGNAL SIGNAL C = COMMON GROUND CONNECTION L L 01 GND (TX) ---- 20 GND (RX) NC = NOT CONNECTED 02 TX2n ---> 21 RX2n = CONNECTION TO A DEVICE ON THE PCB 03 TX2p ---> 22 RX2p 04 GND (TX) ---- 23 GND (RX) 05 TX4n ---> 24 RX4n 06 TX4p ---> 25 RX4p K K 07 GND (TX) ---- 26 GND (RX) 08 ModSelL 27 ModPrsL 09 ResetL 28 IntL 10 VccRx 29 VccTx NC 11 SCL 30 Vcc1 PAD 20 J J 12 SDA 31 LPmode (TOP OF BOARD) 13 GND (RX) ---- 32 GND (TX) 14 RX3p <--- 33 TX3p 15 RX3n <--- 34 TX3n 16 GND (RX) ---- 35 GND (TX) PAD 19 17 RX1p <--- 36 TX1p H PAD 38 H (BOTTOM OF BOARD) 18 RX1n <--- 37 TX1n (TOP OF BOARD) 19 GND (RX) ---- 38 GND (TX) 20 GND (RX) ---- 01 GND (TX) BEZEL 21 RX2n <--- 02 TX2n PAD 01 22 RX2p <--- 03 TX2p (BOTTOM OF BOARD) 23 GND (RX) ---- 04 GND (TX) G G 24 RX4n <--- 05 TX4n 25 RX4p <--- 06 TX4p 26 GND (RX) ---- 07 GND (TX) 27 ModPrsL 08 ModSelL CABLE BEND RADIUS 28 IntL 09 ResetL 29 VccTx 10 VccRx F F NC 30 Vcc1 11 SCL 22.8 MIN BEND RADIUS 31 LPMode 12 SDA NOTE: 32 GND (TX) ---- 13 GND (RX) VIEW NOT TO SCALE. MIN BEND RADIUS MIN BEND SPACE CABLE AWG 33 TX3p ---> 14 RX3p (mm) (mm) 34 TX3n ---> 15 RX3n 24 51 84 E E 35 GND (TX) ---- 16 GND (RX) 26 44 76 36 TX1p ---> 17 RX1p 28 39 70 37 TX1n ---> 18 RX1n 30 33 62 38 GND (TX) ---- 19 GND (RX) MIN BEND SPACE D D C C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE CURRENT REV DESC: OBSOLETED PART NO mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) EC NO: 611198 QSFP+ COPPER PATCH CABLE ASSEMBLY ANGULAR TOL 0.5 CABLE ASSEMBLY DRWN: AKUMAR19 2018/12/31 4 PLACES CHK D: GGA 2019/02/28 B NOTES: B 3 PLACES APPR: GGA 2019/02/28 PRODUCT CUSTOMER DRAWING 1. DC BLOCKING CAPS ON RECEIVE SIDE ONLY 2 PLACES 0.13 INITIAL REVISION: DOCUMENT NUMBER DOC TYPE DOC PART REVISION 2. CABLE COILED AND PACKAGED IN BEST FIT ESD BAG 1 PLACE 0.25 DRWN: SCHANNARAYAN 2017/08/22 AND SEALED WITH ESD LABEL FOR SHIPPING PSD 000 1110400001 Y 0 PLACES APPR: ARAYBURN 2017/09/06 MATERIAL NUMBER THIRD ANGLE PROJECTION DRAWING SERIES CUSTOMER SHEET NUMBER DRAFT WHERE APPLICABLE MUST REMAIN A A SEE P/N TABLE GENERAL MARKET 2 OF 3 D-SIZE 111040 DOCUMENT STATUS P1 RELEASE DATE 2019/02/28 12:46:47 WITHIN DIMENSIONS FORMAT: master-tb-prod-D REVISION: H 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 DATE: 2018/01/18