Hand Crimp Tool for Mini-Fit MAX Terminals Order Number 213309-2300 Application Tooling Specification TYPE 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly terminal locator holds terminals in the proper crimping position Right- or left-handed operation Dies and locator from this tool can be used in the Battery Powered Tool Order No. 63816-0270 (110 V) or 63816-0280 (220 V), with the use of the 63816-0800 Crimp Head This tool is IPC/WHMA-A-620 Class 2 compliant, as indicated on page 2 SCOPE Products: Mini-Fit MAX Receptacle Crimp Terminals, 16 AWG, UL1007 wire. Terminal Terminal Order No. Wire Size Insulation Diameter (1) Strip Length Series No. Reel Loose AWG mm In. mm In. 212515-3102* 212515 212515-3202* 16 2.25-2.40 .089-.094 4.50-5.50 .180-.220 212515-3302* (1) To achieve optimum IPC/WHMA-A-620 insulation crimps, use this insulation OD range. See page 2 for more information. * Not available in loose piece. Cut terminal from reel with 0.15mm max cut-off tab. DEFINITION OF TERMS BEND UP BRUSH CONDUCTOR BELL MOUTH CRIMP INSULATION ROLL CRIMP SEE NOTE TWIST STRIP BEND LENGTH DOWN CRIMP HEIGHT Doc. No: 2133092300 Release Date: 03-30-20 UNCONTROLLED COPY Page 1 of 8 Revision: A Revision Date: 03-30-20 Hand Crimp Tool for Mini-Fit MAX Terminals CONDITIONS After crimping, the crimped terminal should measure as follows: Conductor Crimp Wire Size Terminal Series No. Height Width AWG mm In. mm In. 212515 16 1.40-1.50 .055-.059 2.40-2.50 .094-.098 Insulation Crimp Pull Force Wire Size Terminal Series No. Height (Ref.) Width (Ref.) Minimum AWG mm In. mm In. N Lb. 212515 16 2.30-2.70 .091-.106 2.72-2.82 .107-.111 134 30 To achieve IPC/WHMA-A-620 Class 2 crimps, the following overall wire insulation diameter range is recommended: 2.25-2.40mm (.089-.094) or UL1007 Crimp attribute specifications are as follows: Terminal Series Wire Size Bell Mouth Brush Bend Bend Twist Roll No. Up Down AWG mm In. mm In. 212515 16 0.50-1.00 .020-.039 0.50-1.50 .020-.059 3 3 3 5 Tool Qualification Notes 1. (Ref) means that the dimension provided is approximate because of the wide range of wires, conductor stranding, insulation diameter and insulation hardness. 2. An occasional conductor crimp height measurement should be performed. It must lie between the minimum and maximum crimp height specification. 3. Pull force should be measured with no influence from the insulation crimp. To ensure this, strip the wire long enough so the terminal insulation grips do not contact the wire insulation. Notes 1. This tool should only be used for the terminals and wire gauges specified on this sheet. 2. Variations in tools, terminals, wire stranding and insulation types may affect crimp height. 3. This tool is intended for AWG conductor sizes. It may not give good insulation crimp support for insulation sizes outside of the specified range. 4. Molex does not repair hand tools. See warranty on page 6. The replacement parts listed are the only parts available for repair. If the handles or crimp tooling become damaged or worn, a new tool must be purchased. 5. Conductor crimp height should be used as the final criterion for an acceptable crimp. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping and crimp testing. 6. Molex does not certify crimp hand tools. Note The crimp height chart is provided with this document as reference only. Due to the wide range of wires, strands, insulation diameters and insulation hardness available, actual crimp height measurements may vary slightly. An occasional destructive pull force test should be performed to verify the conductor crimp. The pull force value must exceed the minimum pull force specifications listed. Doc. No: 2133092300 Release Date: 03-30-20 UNCONTROLLED COPY Page 2 of 8 Revision: A Revision Date: 03-30-20