Hand Crimp Tool for .093 Pin and Socket Crimp Terminals Order No. 63828-1200 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly terminal locator wire stop holds terminals in the proper crimping position Right- or left-handed operation Dies and locator from this tool can be used in the Battery Powered Tool Order No. 63816-0200 (110 V) or 63816-0250 (220 V), with the use of the 63816-0800 Crimp Head This tool is IPC/WHMA-A-620 Class 2 compliant, as indicated on page 2 This tool is RoHS compliant however, RoHS compliance is not required SCOPE Products: .093 Pin and Socket Crimp Terminals, 20 AWG. Terminal Order No. Wire Size Insulation Diameter + Strip Length Terminal Series No. Loose Piece Reel AWG mm In. mm In. 02-09-1123 02-09-1122 2273 20 1.45-2.55 .057-.100 4.00-5.00 .157-.196 02-09-1140 02-09-1135 Reeled terminals must be properly cut from the reel. See Terminal Cutoff Specifications on page 2. +See Conditions on page 2. DEFINITION OF TERMS BEND UP BRUSH CONDUCTOR BELL MOUTH CRIMP INSULATION ROLL CRIMP SEE NOTE TWIST STRIP BEND LENGTH DOWN CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc. No: 638281200 Release Date: 04-30-18 UNCONTROLLED COPY Page 1 of 7 Revision: B Revision Date: 06-19-20 Hand Crimp Tool for .093 Pin and Socket Crimp Terminals CONDITIONS After crimping, the conductor profiles should measure the following: Wire Conductor Crimp Insulation Crimp Pull Force Profile Size Minimum Terminal Height Width (Ref.) Height (Ref.) Width (Ref.) AWG mm In. mm In. mm In. mm In. N Lb. A B C 2.70 .106 2.10 .083 X 2273 20 1.11-1.17 .044-.046 1.88 .074 2.85 .112 2.80 .110 67 15 X 2.60 .102 2.00 .079 X To achieve IPC/WHMA-A-620 Class 2 crimps, the following overall wire insulation diameter ranges are recommended: Profile A: 1.65-2.15mm (.065-.084) or UL1007 Profile B: 2.35-2.55mm (.093-.100) or UL1015 Profile C: 1.45-1.85mm (.057-.072) or UL1061 Tool Qualification Notes 1. (Ref) means that the dimension provided is approximate because of the wide range of wires, conductor stranding, insulation diameter and insulation hardness. 2. An occasional pull force test should be performed. It must exceed the minimum pull force specification. 3. Pull force should be measured with no influence from the insulation crimp. To ensure this, strip the wire long enough so the terminal insulation grips do not contact the wire insulation. Note A crimp height chart is provided with this document as a reference only. Because of the wide range of wires, strands, insulation diameters and durometers available, actual crimp height measurements may very slightly. An occasional destructive pull force test should be performed to check hand tool crimp. Pull force value must exceed the minimum pull force specifications listed. Terminal Cutoff Specifications This hand tool operates best with loose-piece terminals. If reeled terminals are used, they must be cut from the carrier strip as specified below: Terminal Reeled Terminal Cutoff Dimension X Series No. Order No. mm In. 02-09-1122 2273 3.610.08 .142.003 02-09-1135 2273 SERIES Doc. No: 638281200 Release Date: 04-30-18 UNCONTROLLED COPY Page 2 of 7 Revision: B Revision Date: 06-19-20