63902-3270 Molex

Fine Adjust Applicator for SL Crimp Terminals FineAdjust Applicator Application Tooling Specification Sheet Order No. 63902-3200 FEATURES Quick punch removal with the push of a button for fast and easy tooling change Applicator designed to industry standard mounting and shut height 135.80mm (5.346 ) Quick set-up time plus the crimp height, track and feed adjustments can be set without removing the applicator from the press Fine adjustment allows users to achieve target with little effort by adjusting in increments of .015mm (.0006 ) for conductor crimp height and .063mm (.0025 ) for insulation height Independent adjustment rings allow users to quickly adjust the conductor or insulation crimp height without affecting each other Directly adapts to most automatic wire processing machines SCOPE Products: SL Female Crimp Terminal, 22-24 AWG. Wire Size Insulation Diameter Strip Length Terminal Series No Terminal Order No. AWG mm mm In. mm In. 016-02-0086 016-02-0152 70058-4086 016-02-0087 70058-0086 70058-5001 70058 22-24 0.20-0.35 1.40-1.63 .055-.064 3.17-3.56 .125-.140 016-02-0088 70058-0087 016-02-0131 70058-0088 71851 016-02-1110 016-02-1111 016-02-1124 22-24 0.20-0.35 1.40-1.63 .055-064 3.17-3.56 .125-.140 BEND UP DEFINITION OF TERMS ROLLING SEAM BELL BRUSH CONDUCTOR MOUTH CRIMP INSULATION CRIMP TWISTING STRIP LENGTH BEND DOWN CUT-OFF TAB CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-639023200 Release Date: 11-09-10 UNCONTROLLED COPY Page 1 of 5 Revision: B Revision Date: 08-28-13 Fine Adjust Applicator for SL Crimp Terminals CRIMP SPECIFICATION Cut-off Tab Maximum Bell mouth Conductor Brush Terminal Series No. Front Rear mm In. mm In. mm In. mm In. 70058 0.20-0.50 .008-.020 0.13 .005 .08 .003 0.00-1.00 .000-.039 71851 0.20-0.50 .008-.020 0.13 .005 .08 .003 0.00-1.00 .000-.039 Bend up Bend down Twist Roll Punch Width mm (Ref) Seam Terminal Series No. Conductor Insulation Degree Degree Seam shall not be open mm In mm In and no wire allowed out 70058 3 3 3 8 1.40 .055 1.70 .067 of the crimping area 71851 3 3 3 8 1.40 .055 1.70 .067 After crimping, the conductor profile should measure the following. Wire Size Crimp Height Pull Force Minimum Terminal Series No. 2 AWG mm mm In. N Lb. 22 0.35 0.84-0.89 .033-.035 35.6 8.0 70058 24 0.20 0.76-0.81 .030-.032 22.2 5.0 22 0.35 0.84-0.89 .033-.035 35.6 8.0 71851 24 0.20 0.76-0.81 .030-.032 22.2 5.0 Tool Qualification Notes: 1. Pull Force should be measured with no influence from the insulation crimp. 2. The above specifications are guidelines to an optimum crimp. Doc No: ATS-639023200 Release Date: 11-09-10 UNCONTROLLED COPY Page 2 of 5 Revision: B Revision Date: 08-28-13