SPEC No.JENF243A-0084C-01 P.1/7 Reference Only Noise Filter BLF03JDGN Reference Specification 1.Scope This reference specification applies to Noise Filter BLF03JD GN Series. 2.Part Numbering (Ex) BL F 03 JD 421 G N E D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (7)Category (2)Type (8)Rated Current No (3)Dimension (LW) (9)Packaging (4)Characteristics D:Taping (5)Typical Impedance at 700MHz B:Bulk (6)Performance *Bulk packing also available. (A product is put in the plastic bag under the taping conditions.) 3Rating *1Rated Current DC Resistance Impedance () ( max.) (mA) Customer MURATA (at 700MHz, Values Part Number Part Number Under Standard Initial at 125C at 85C After Testing Condition) Values Testing BLF03JD421GNED 480 370 0.28 0.38 42040% Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C 1 (Note) As for the Rated current marked with * , Rated Current is derated as right figure depending on the operating temperature. 4.Style and Dimensions Equivalent Circuit Resistance element becomes () dominant at high frequencies. Unit Mass (Typical value) L 0.60.03 0.400mg W 0.30.03 T 0.40.03 e 0.150.05 5.Marking No marking. 6.Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa MURATA MFG.CO.,LTD. SPEC No.JENF243A-0084C-01 P.2/7 Reference Only 7.Specifications 7-1.Electrical Performance No. Item Specification Test Method 7-1-1 Impedance Meet item 3. Measuring Frequency : 700MHz1MHz Measuring Equipment : KEYSIGHT4991A or the equivalent Test Fixture : KEYSIGHT 16192A or the equivalent 7-1-2 DC Meet item 3. Measuring Equipment : Digital multi meter Resistance * Except resistance of the Substrate and Wire 7-2.Mechanical Performance No. Item Specification Test Method 7-2-1 Bonding Products shall not be damaged It shall be soldered on the substrate. Strength after tested as test method. Applying Force : 1N Applying Time : 5s 7-2-2 Bending It shall be soldered on the Glass-epoxy substrate. Strenght Substrate : 100mm40mm0.8mm Deflection : 2mm Speed of Applying Force : 1.0mm/s Keeping Time : 20s Pressure jig R230 F Deflection 45 45 Product 7-2-3 Vibration Appearance: No damage It shall be soldered on the substrate. Oscillation Frequency : 10Hz to 2000Hz to 10Hz for 20min Total amplitude 3.0mm or Acceleration 2 amplitude 196 m / s whichever is smaller. Testing Time : A period of 2h in each of 3 mutually perpendicular directions.(Total 6h) 7-2-4 Solderability The electrodes shall be at Flux : Ethanol solution of rosin,25(wt)% least 95% covered with new Pre-Heating : 150C, 60s solder coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 245C3C Immersion Time : 3s 7-3.Environmental Performance It shall be soldered on the substrate. No. Item Specification Test Method 7-3-1 Heat Life Meet Table 1. Temperature : 125C2C Table 1 Applying Current : Rated Current (at 125C) Time : 1000h(+48h,-0h) Appearance No damage Then measured after exposure in the room Impedance condition for 4 to 48 h. Change Within 30% (at 700MHz) 7-3-2 Cold Temperature : -55C2C Resistance DC Time : 1000h(+48h,-0h) Meet item 3. Resistance Then measured after exposure in the room condition for 4 to 48 h. 7-3-3 Humidity Temperature : 40C2C Humidity : 90%(RH) to 95%(RH) Time : 1000h(+48h,-0h) Then measured after exposure in the room condition for 4 to 48 h. 7-3-4 Temperature 1 cycle : Cycle 1 step : -55 C(+0 C,-3 C) /30min(+3min,-0min) 2 step : Ordinary temp. / 3 min max. 3 step : +125 C(+3 C,-0 C) / 30min(+3min,-0min) 4 step : Ordinary temp. / 3 min max. Total of 100 cycles Then measured after exposure in the room condition for 4 to 48 h. MURATA MFG.CO.,LTD.