BLM15HB121SN1D Murata

Reference Only Spec.No.JENF243A-0024M-01 P1/9 GHz Noise Suppression Chip Ferrite Bead BLM15HSN1 Reference Specification 1.Scope This Reference Specification applies to Chip Ferrite Bead BLM15H SN series. 2.Part Numbering (ex.) BL M 15 HG 601 S N 1 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (2)Type (3)Dimension(L) (4)Characteristics (5)Typical Impedance at 100MHz (6)Performance (7)Category (8)Numbers of Circuit (9)Packaging(D:Taping / B:Bulk) 3.Rating Impedance () DC Resistance (Under Standard Rated ( max.) Customer MURATA Testing Condition) Current Initial Values Remark Part Number Part Number (mA) Values After at 100MHz at 1GHz Testing BLM15HG601SN1D 0.7 max 60025% 100040% 300 0.8 max For BLM15HG601SN1B general BLM15HG102SN1D 1.1 max 100025% 140040% 250 1.2 max use BLM15HG102SN1B BLM15HD601SN1D 60025% 140040% 300 0.85 max 0.95 max BLM15HD601SN1B BLM15HD102SN1D 100025% 200040% 250 1.25 max 1.35 max BLM15HD102SN1B For BLM15HD182SN1D 180025% 270040% 200 2.2 max 2.3 max High speed BLM15HD182SN1B Signal line BLM15HB121SN1D 12025% 50040% 300 0.7 max 0.8 max BLM15HB121SN1B BLM15HB221SN1D 1.0 max 22025% 90040% 250 1.1 max BLM15HB221SN1B Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C 4.Style and Dimensions 1.00.05 0.50.05 Equivalent Circuit 0.250.1 Resistance element becomes () dominant at high frequencies. :Electrode (in mm) Unit Mass (Typical value) 0.001g 5.Marking No marking. 6.Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa MURATA MFG.CO.,LTD. 0.50.05Reference Only Spec.No.JENF243A-0024M-01 P2/9 7.Specifications 7-1.Electrical Performance No. Item Specification Test Method 7-1-1 Impedance Meet item 3. Measuring Frequency : 100MHz1MHz , 1GHz1MHz Measuring Equipment : KEYSIGHT4291A or the equivalent Test Fixture : KEYSIGHT16192A or the equivalent 7-1-2 DC Resistance Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 7-2.Mechanical Performance No. Item Specification Test Method 7-2-1 Appearance and Meet item 4. Visual Inspection and measured with Slide Calipers. Dimensions 7-2-2 Bonding Meet Table 1. It shall be soldered on the substrate. Strength Applying Force(F) : 5N Table 1 Applying Time : 5s1s Applying Direction: Parallel to the substrate. Appearance No damage Side view Impedance Change Within 30% R0.5 (at 100MHz) DC Meet item 3. Resistance Substrate 7-2-3 Bending It shall be soldered on the substrate. Strength Substrate: Glass-epoxy 100mm40mm0.8mm Deflection : 2.0mm Speed of Applying Force : 0.5mm/s Keeping Time : 30s Pressure jig R340 F Deflection 45mm 45mm Product 7-2-4 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10Hz to 2000Hz to 10Hz for 20 min 2 Total Amplitude 1.5mm or Acceleration 196m/s whichever is smaller Testing Time : A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 h) 7-2-5 Resistance Pre-Heating : 150C10C, 60s90s to Soldering Solder : Sn-3.0Ag-0.5Cu Heat Solder Temperature : 270C5C Immersion Time : 10s0.5s Immersion and emersion rates : 25mm/s Then measured after exposure in the room condition for 48h4h. 7-2-6 Drop Products shall be no failure It shall be dropped on concrete or steel board. after tested. Method : free fall Height : 75cm Attitude from which the product is dropped : 3 direction The number of times : 3 times for each direction (Total 9 times) MURATA MFG.CO.,LTD.