Spec No.: JENF243A 9121E-01 P1/9 GHz NOISE SUPPRESSION CHIP FERRITE BEAD BLM15H SZ1 Murata Standard Reference Specification AEC-Q200 1. Scope This reference specification applies to chip ferrite bead BLM15H SZ series for automotive electronics based on AEC-Q200 except for power trains and safeties. 2. Part Numbering (Ex.) BL M 15 HG 601 S Z 1 D Product Type Dimension Characteristics Impedance Performance Category Numbers of Packaging ID (L W) (Typical value circuit D: taping at 100 MHz) B: bulk 3. Part Number and Rating Operating temperature range -55C to +125C Storage temperature range -55C to +125C Impedance DC resistance ( ) () max. Rated ESD Customer Murata current Remark rank Values Part number Part number Initial (mA) 2: 2 kV at 100 MHz at 1 GHz after values testing BLM15HG601SZ1D 60025% 100040% 300 0.7 0.8 For general use 2 BLM15HG102SZ1D 100025% 140040% 250 1.1 1.2 For general use 2 BLM15HD601SZ1D 60025% 140040% 300 0.85 0.95 For high speed 2 signal line BLM15HD102SZ1D 100025% 200040% 250 1.25 1.35 For high speed 2 signal line BLM15HD182SZ1D 180025% 270040% 200 2.2 2.3 For high speed 2 signal line BLM15HB121SZ1D 12025% 50040% 300 0.7 0.8 For high speed 2 signal line BLM15HB221SZ1D 22025% 90040% 250 1.0 1.1 For high speed 2 signal line 4. Testing Conditions Unless otherwise specified Temperature: ordinary temperature (15C to 35C) Humidity: ordinary humidity 25% to 85% (RH) In case of doubt Temperature: 20C2C Humidity: 60% to 70% (RH) Atmospheric pressure: 86 kPa to 106 kPa 5. Appearance and Dimensions Equivalent circuit Unit mass (typical value): 0.001 g MURATA MFG CO., LTD Spec No.: JENF243A 9121E-01 P2/9 6. Marking No marking. 7. Electrical Performance No. Item Specification Test method 7.1 Impedance Meet chapter 3 ratings. Measuring equipment: Keysight 4291A or the equivalent Measuring frequency: 100 MHz1 MHz, 1 GHz1 MHz Measuring fixture: Keysight 16192A or the equivalent 7.2 DC resistance Meet chapter 3 ratings. Measuring equipment: digital multimeter Substrate wiring resistance is excluded. 8. AEC-Q200 Requirement 8.1 Performance (based on table 13 for filter EMI suppressors/filters) AEC-Q200 Rev.D issued June 1, 2010 AEC-Q200 Murata specification/deviation No. Stress Test method 3 High 1000 h at 125C Meet table A after testing. temperature Set for 24 h at room condition, then Table A exposure measured. Appearance No damage Impedance change (at 100 MHz) Within 30% Meet chapter 3 DC Resistance ratings. 4 Temperature 1000 cycles Meet table A after testing. cycling -55C to +125C Set for 24 h at room condition, then measured. 5 Destructive Per EIA469 No defects physical No electrical tests analysis 7 Biased humidity 1000 h at 85C, 85% (RH). Meet table A after testing. Apply max rated current. Set for 24 h at room condition, then measured. 8 Operational life Apply 125C 1000 h Meet table A after testing. Set for 24 h at room condition, then If the rated current of parts exceed 1A, the operating measured. temperature should be 85 C. 9 External visual Visual inspection No abnormalities 10 Physical Meet chapter 5,Appearance and No defects dimension Dimension. 12 Resistance to Per MIL-STD-202 Not applicable solvents Method 215 13 Mechanical Per MIL-STD-202 Meet table A after testing. shock Method 213 Condition F: 1500 gs (14.7 N), 0.5 ms, half sine 14 Vibration 5 g s (0.049 N) for 20 min, 12 cycles Meet table A after testing. each of 3 orientations Test from 10 Hz to 2000 Hz 15 Resistance to Solder temperature Pre-heating: 150C10C, 60 s to 90 s soldering heat 260C5C Meet table A after testing. Immersion time 10 s 17 ESD Per AEC-Q200-002 ESD rank: Refer to chapter 3 ratings. Meet table A after testing. 18 Solderbility Per J-STD-002 Method b: not applicable 95% of the terminations is to be soldered. 19 Electrical Measured: impedance No defects characterization MURATA MFG CO., LTD