BLM18EG471SZ1D Murata

Reference Only Spec. No. JENF243A-9124A-01 P.1/8 GHz Noise Suppression Chip Ferrite Bead BLM18EGZ1 Murata Standard Reference Specification AEC-Q200 1. Scope This reference specification applies to Chip Ferrite Bead BLM18EG Z Series for Automotive Electronics based on AEC-Q200 except for Power train and Safety. 2. Part Numbering (ex.) BL M 18 EG 601 S Z 1 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (2)Type (3)Dimension(LW) (4)Characteristics (5)Typical Impedance at 100MHz (6)Performance (7)Category(for Automotive Electronics) (8)Numbers of Circuit (9)Packaging(D:Taping) 3. Rating DC Resistance Impedance () (Under Standard Testing Condition) ( max. ) (*1) (*1) (refer to below comment) Rated refer to below Customer MURATA ESD Rank comment) Current Remark 2:2kV Part Number Part Number (mA) Initial Values at 1GHz at 100MHz Values After Typical Testing BLM18EG101TZ1D 10025% 80 min. 140 2000 0.045 0.07 For BLM18EG221TZ1D 22025% 180 min. 300 1000 0.15 0.21 general 2 use BLM18EG331TZ1D 33025% 280 min. 450 500 0.21 0.30 (Thin type) BLM18EG391TZ1D 39025% 320 min. 520 500 0.30 0.40 BLM18EG121SZ1D 12025% 90 min. 145 2000 0.04 0.06 For BLM18EG221SZ1D 22025% 160 min. 260 2000 0.05 0.06 general 2 BLM18EG471SZ1D 47025% 340 min. 550 500 0.21 0.30 use BLM18EG601SZ1D 60025% 450 min. 700 500 0.35 0.45 Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C (*1) Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa 3 As for BLM18EG type,Rated Current is derated as right figure 2A 2 depending on the operating temperature. 1 0 85 125 Operating Temperature 4. Style and Dimensions 1.60.15 0.80.15 Equivalent Circuit 0.40.2 Resistance element becomes () dominant at high frequencies. :Electrode Unit Mass (Typical value) BLM18EGTZ1 : 0.004g BLM18EGSZ1 : 0.005g Part Number Dimension(T) 0.50.15 BLM18EGTZ1 0.80.15 (in mm) BLM18EGSZ1 MURATA MFG.CO., LTD. T R at e d Cur r e ntReference Only Spec. No. JENF243A-9124A-01 P.2/8 5. Marking No marking. 6. Specifications 6-1. Electrical Performance No. Item Specification Test Method 6-1-1 Impedance Meet item 3. Measuring Frequency : 100MHz1MHz , 1GHz1MHz Measuring Equipment : KEYSIGHT 4291A or the equivalent Test Fixture : KEYSIGHT 16192A or the equivalent 6-1-2 DC Resistance Meet item 3. Measuring Equipment : Digital multi meter *Except resistance of the Substrate and Wire 6-2. Mechanical Performance(based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No.Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours at room Table A Exposure temperature, then measured. Appearance No damage Impedance Change Within 30% (at 100MHz) DC Meet item 3. Resistance Meet Table B. 4 Temperature Cycling 1000cycles Table B -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. Appearance No damage Impedance Within Change +50%/-10% (at 100MHz) DC Meet item 3. Resistance 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. Apply max rated current. 9 External Visual Visual inspection No abnormalities 8 Operational Life Apply 125 deg C 1000hours Meet Table A after testing. If the rated current of parts exceed 1A, Set for 24hours at room the operating temperature should be 85 deg C. temperature, then measured No defects 10 Physical Dimension Meet ITEM 4 Style and Dimensions 12 Resistance to Solvents Per MIL-STD-202 Not Applicable Method 215 13 Mechanical Shock Per MIL-STD-202 Method 213 Meet Table A after testing. Condition F 1500g s (14.7N)/0.5ms/ Half sine Meet Table A after testing. 14 Vibration 5g s(0.049N) for 20 minutes, 12cycles each of 3 orientations Test from 10-2000Hz. 15 Resistance Solder temperature Pre-heating:150C +/-10 deg,60s to 90s Meet Table A after testing. to Soldering Heat 260C+/-5 deg C Immersion time 10s MURATA MFG.CO., LTD.