BLM41PG471SH1L Murata

Spec. No. JENF243A-9106N-01 Re f e re n c e O nl y P.1/10 Chip Ferrite Bead BLM41SH1L Murata Standard Reference Specification AEC-Q200 1. Scope This reference specification applies to Chip Ferrite Bead for Automotive Electronics BLM41 SH Series based on AEC-Q200. 2. Part Numbering (ex.) BL M 41 PG 600 S H 1 L (1) (2) (3) (4) (5) (6) (7) (8) (9) (1)Product ID (4)Characteristics (7)Category(for Automotive Electronics) (2)Type (5)Typical Impedance at 100MHz (8)Numbers of Circuit (3)Dimension (L) (6)Performance (9)Packaging (L:Taping) 3. Rating Impedance () DC Resistance (at 100MHz,Under Standard () max. (*1) Rated Current Testing Condition) (refer to below (mA) (*2) Customer MURATA ESD Rank comment) (*1) Part Number Part Number 6:25kV Initial Values (refer to below comment) Values After at at Typical Testing 85C 125 *2 *2 BLM41PG600SH1L 30 min. 60 0.009 0.018 6000 3700 *2 *2 BLM41PG750SH1L 45 min. 75 0.015 0.03 3500 2450 *2 *2 BLM41PG181SH1L 18025% 180 0.02 0.04 6 3500 2100 *2 *2 BLM41PG471SH1L 47025% 470 0.05 0.10 2000 1350 *2 *2 BLM41PG102SH1L 100025% 1000 0.09 0.18 1500 1000 Operating Temperature: -55C to +125C Storage Temperature: -55C to +125C (*1) Standard Testing Conditions < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa 85 x (*2) In case of Rated current is more than *1, Describe the Rated current as x A in case of more than 1A. Rated Current is derated as right figure depending on the operating temperature. 1251 0 85 125 4. Style and Dimensions Operating Temperature (C) 4.50.2 1.60.2 Equivalent Circuit 0.70.3 Resistance element becomes () dominant at high frequencies. : Electrode Unit Mass (Typical value) 0.050g (in mm) MURATA MFG.CO., LTD. 1.60.2 Rated Current (A)Spec. No. JENF243A-9106N-01 Re f e re n c e O nl y P.2/10 5. Marking No marking. 6. Specifications 6-1. Electrical Performance No. Specification Test Method Impedance Meet item 3. Measuring Frequency : 100MHz1MHz 6-1-1 Measuring Equipment : KEYSIGHT 4291A or the equivalent Test Fixture : KEYSIGHT 16192A or the equivalent Measuring Equipment : Digital multi meter 6-1-2 DC Resistance Meet item 3. *Except resistance of the Substrate and Wire 6-2. Mechanical Performance (based on Table 13 for FILTER EMI SUPPRESSORS/ FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours at room Table A Exposure temperature, then Appearance No damage measured. Impedance Change Within 30% (at 100MHz) DC Meet item 3. Resistance 4 Temperature Cycling 1000cycles Meet Table A after testing. -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, Meet Table A after testing. 85%RH Apply max rated current. Meet Table A after testing. 8 Operational Life Apply 125 deg C If the rated current of parts exceed 1A, 1000hours the operating temperature should be 85 deg C. Set for 24hours at room temperature, then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 4 No defects Style and Dimensions 12 Resistance to Solvents Per MIL-STD-202 Method Not Applicable 215 13 Mechanical Shock Per MIL-STD-202 Method Meet Table A after testing. 213 Condition F: 1500gs(14.7N)/0.5ms/ Half sine 14 Vibration 5g s(0.049N) for 20 Meet Table A after testing. minutes, 12cycles each of 3 orientations Test from 10-2000Hz. MURATA MFG.CO., LTD.