Reference Only Spec No.JEFL243D-0009M-01 P1/11 Chip Common Mode Choke Coil DLM0NSHY2 Reference Specification 1.Scope This reference specification applies to Chip Common Mode Choke Coil DLM0NS Series for differential signal interface in Electronics. 2. Part Numbering (ex.) DL M 0N S B 120 H Y 2 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Impedance (Typ. at 100MHz) (2) Structure (M : Monolithic Type) (7) Circuit H : Characteristic Impedance 100 system (3) Dimension (LW) (8) Features (4) Type S: Magnetically shielded one circuit type (9) Number of Line (5) Category (10) Packaging Code D : Taping / B : Bulk 3. Rating Common Mode Impedance Customer Murata Rated Withstanding Rated DC Insulation Cut-off (at 100MHz, Under Part Number Part Number Voltage Voltage Current Resistance Resistance Frequency Standard Testing Condition) DLM0NSB120HY2D 125 160mA 1.225% DLM0NSB120HY2B 10M 5V(DC) 12.5V(DC) 8GHz(Typ.) DLM0NSB280HY2D min. 2830% 130mA 1.925% DLM0NSB280HY2B DLM0NSN500HY2D 5025% 2.725% 5GHz(Typ.) DLM0NSN500HY2B 10M 5V(DC) 12.5V(DC) 100mA min. DLM0NSN900HY2D 9025% 4.025% 2GHz(Typ.) DLM0NSN900HY2B DLM0NSM900HY2D 10M 9025% 5V(DC) 12.5V(DC) 100mA 3.825% 5GHz(Typ.) min. DLM0NSM900HY2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions Equivalent Circuits (1) (2) (4) (3) No polarity No polarity Unit Mass(Typical value) 0.9mg 0.200.10 MURATA MFG.CO., LTD Reference Only Spec No.JEFL243D-0009M-01 P2/11 6.Marking No Marking. 7. Electrical Performance No. Item Specification Test Method 7.1 Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 10.) Impedance Measuring Equipment : KEYSIGHT 4291A or the equivalents (In case of doubt in standard condition, the heat treatment(200C, about 10 min) shall be applied. 7.2 Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage Voltage Time : 1 to 5s Charge Current : 1 mA max.(ref.item 10.) 7.3 DC Resistance Meet item 3. Measuring current : 100mA max.(ref.item 10.) (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Resistance (I.R.) Measuring time : 1 min max. (ref.item 10.) 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 15010C, 6090s coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2303C Immersion Time : 30.5s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 15010C, 6090s Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 51s Impedance within 30% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition 10M min. I.R. for 4h to 48h. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 10 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 2000 for 20 min Total amplitude : 3.0 mm or Acceleration amplitude 2 196 m/s whichever is smaller. Testing Time : A period of 4 hours in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : (t =1.0 mm). Strength Table 2 Deflection : 2 mm Speed of Applying Force : 1.0 mm / s Appearance No damaged Keeping time : 60s DC Resistance within 30% Pressure jig Change R230 F Deflection 45 45 Product MURATA MFG.CO., LTD