DLM11SN450HZ2L Murata

Reference Only Spec No. JEFL243C-9116F-01 P1/10 Chip Common Mode Choke Coil DLM11SNHZ2 Murata Reference Specification AEC-Q200 1.Scope This reference specification applies to Chip Common Mode Choke Coil DLM11S Series for Automotive Electronics based on AEC-Q200 except for Power train and Safety. 2.Part Numbering (ex.) DL M 11 S N 900 H Z 2 L (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Impedance (Typ. at 100MHz) (2) Structure (M : Monolithic Type) (7) Circuit H : Characteristic Impedance 100 system (3) Dimension (LW) (8) Features (4) Type S: Magnetically shielded one circuit type (9) Number of Line (5) Category (10) Packaging Code L : Taping / B : Bulk 3.Rating Common Mode Impedance ESD Customer Murata Rated Withstanding Rated DC Insulation Rank (at 100MHz, Under Part Number Part Number Voltage Voltage Current Resistance Resistance 2:2kV Standard Testing Condition) DLM11SN450HZ2L 4525% 0.725% DLM11SN450HZ2B 100M 5V(DC) 12.5V(DC) 100mA 2 min. DLM11SN900HZ2L 9025% 1.125% DLM11SN900HZ2B Operating Temperature : -55 to +125C Storage Temperature : -55 to +125C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions Equivalent Circuits (1) (2) (1) (2) (Top View) (4) (3) (3) (4) 0.3 0.1 No polarity (Side View) Unit Mass (Typical value) 0.004g Electrode (Bottom View) In mm 0.2 0.15 1.25 0.1 6.Marking No Marking. MURATA MFG.CO.,LTD 1.0 0.1 0.55 0.1 0.5 0.1 Reference Only Spec No. JEFL243C-9116F-01 P2/10 7. Electrical Performance No. Item Specification Test Method 7.1 Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 9.) Impedance Measuring Equipment : KEYSIGHT 4991A or the equivalents (In case of doubt in standard condition, the heat treatment (200C,about 10 minutes)shall be applied. 7.2 Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage Voltage Time : 1 to 5 seconds Charge Current : 1 mA max.(ref.item 9.) 7.3 DC Resistance Meet item 3. Measuring current : 10mA max.(ref.item 9.) (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Resistance (I.R.) Measuring time : 1 minute max. (ref.item 9.) 8. Q200 Requirement 8-1. Performance (based on Table 13 for Ferrite EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June 1. 2010 AEC-Q200 Murata Specification / Deviation Stress Test Method No. High 1000hours at 125 deg C 3 Meet Table A after testing. Temperature Set for 24hours at room Exposure temperature, then measured. Table A Appearance No damaged Common Mode Impedance within 20% Change Rdc change within 30% 100M min. I.R. Withstanding No damaged Voltage 4 Temperature Cycling 1000cycles Meet Table A after testing. -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. 5 Per EIA469 No defects Destructive Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, Meet Table A after testing. 85%RH (ref.item 9) Apply max rated current. 8 Operational Life Apply 125 deg C Meet Table A after testing. 1000hours Apply rated current. Set for 24hours at room temperature, then measured (ref.item 9) 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 4 No defects Style and Dimensions 12 Resistance to Solvents Per MIL-STD-202 Method 215 Not Applicable 13 Mechanical Shock Per MIL-STD-202 Method 213 Meet Table A after testing. Condition F: 1500gs(14.7N)/0.5ms/ Half sine MURATA MFG.CO.,LTD