Reference Only Spec No. JEFL243E-0014F-01 P1/10 Chip Common Mode Choke Coil DLP11RBUL2 Reference Specification 1.Scope This reference specification applies to Chip Common Mode Choke Coil DLP11RB series. 2.Part Numbering (ex.) DL P 11 R B 150 U L 2 L (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Common mode Impedance (Typ. at 100MHz) (2) Structure (P : Film Type) (7) Circuit U : Characteristic Impedance 90 system (3) Dimension (LW) (8) Features (4) Magnetic Shield and Low Height Type (9) Number of Line (5) Category: Cut off Frequency 8GHz(Typ.) (10) Packaging Code L : Taping / B : Bulk 3.Rating Common Mode Impedance Customer Rated Withstanding Rated DC Insulation Murata Part Number (at 100MHz, Part Number Voltage Voltage Current Resistance Resistance Under Standard Testing Condition) DLP11RB150UL2L 100M 15+/-5 5 V(DC) 12.5V(DC) 100mA 0.8+/-25% DLP11RB150UL2B min. DLP11RB400UL2L 100M 5 V(DC) 12.5V(DC) 100mA 40+/-10 1.3+/-25% DLP11RB400UL2B min. Differential mode to common mode Impedance Characteristics Murata Part Number conversion characteristics (Scd21) between signal lines Z0 2.5GHz (TDR 50ps) DLP11RB150UL2L -40dB(typ.) 90+/-15 DLP11RB150UL2B DLP11RB400UL2L -40dB(typ.) 90+/-15 DLP11RB400UL2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions (1) (2) Equivalent Circuits (Top View) (1) (2) (4) (3) 0.30 0.10 (3) (4) (Side View) No polarity (Bottom View) :Electrode Unit Mass (Typical value) (in : mm) 0.002g 0.25 +0.10/-0.05 1.250.10 6.Marking No Marking. MURATA MFG.CO.,LTD 1.00 0.10 0.550.10 0.500.10Reference Only Spec No. JEFL243E-0014F-01 P2/10 7. Electrical Performance No. Item Specification Test Method Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 10.) 7.1 Impedance Measuring Equipment : KEYSIGHT4291A or the equivalents (In case of doubt, the heat treatment (200C,about 10 minutes)shall be applied. Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage 7.2 Voltage Time : 1 to 5 seconds Charge Current : 1 mA max.(ref.item 10.) DC Resistance Meet item 3. Measuring current : 100mA max.(ref.item 10.) 7.3 (Rdc) Insulation Resistance Measuring voltage : Rated Voltage 7.4 (I.R.) Measuring time : 1 minute max. (ref.item 10.) Impedance Network Analyzer 7.5 Characteristics Measuring Equipment : E5071B or the equivalents between signal lines (ref.item 10.) (Z0) Differential mode to Network Analyzer 7.6 common mode Measuring Equipment : E5071B or the equivalents conversion characteristics (ref.item 10.) (Scd21) 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 150C, 1minute coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2453C Immersion Time : 31 s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 150C ,1minute Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 101 s Impedance within 20% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition 100M min. I.R. for 4 to 48 hours. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 3 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 55 to 10Hz for 1 minute Total Amplitude : 1.5mm Testing Time : A period of 2 hours in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : (t =1.0 mm). Strength Table 2 Deflection : 2 mm Speed of Applying Force : 0.5 mm / s Appearance No damaged Pressure jig Keeping time : 30 s DC Resistance within 30% R230 F Change Deflection 45 45 Product MURATA MFG.CO.,LTD