DLP11SN161SL2L Murata

Reference Only Spec No. JEFL243E-0004W P1/9 Chip Common Mode Choke Coil DLP11SNL2 Reference Specification 1.Scope This reference specification applies to Chip Common Mode Choke Coil DLP11SN Series. 2.Part Numbering (ex.) DL P 11 S N 201 H L 2 L (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Choke Coil (6) Impedance (Typ. at 100MHz) (2) Structure (P : Film Type) (7) Circuit S : Standard (3) Dimension (LW) H : Characteristic Impedance 100 system (4) Type (8) Features (5) Category (9) Number of Line (10) Packaging Code L : Taping / B : Bulk 3.Rating Common Mode Impedance Customer Murata Rated Withstanding Rated DC Insulation (at 100MHz, Under Part Number Part Number Voltage Voltage Current Resistance Resistance Standard Testing Condition) DLP11SN670SL2L 180mA 67 20% 1.325% DLP11SN670SL2B DLP11SN900HL2L 90 20% 150mA 1.525% DLP11SN900HL2B DLP11SN121SL2L 120 20% 140mA 2.025% DLP11SN121SL2B DLP11SN161SL2L 160 20% 120mA 2.725% DLP11SN161SL2B 100M 5V(DC) 12.5V(DC) DLP11SN201HL2L min. 110mA 20020% 3.125% DLP11SN201HL2B DLP11SN241HL2L 24020% 100mA 3.525% DLP11SN241HL2B DLP11SN281HL2L 28020% 90mA 4.225% DLP11SN281HL2B DLP11SN331HL2L 33020% 80mA 4.925% DLP11SN331HL2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions (1) (2) Equivalent Circuits (Top View) (2) (1) (4) (3) 0.30 0.10 (3) (4) (Side View) No polarity (Bottom View) :Electrode Unit Mass (Typical value) (in : mm) 0.005g 0.25 +0.10/-0.05 MURATA MFG.CO., LTD 1.25 0.10 1.00 0.10 0.55 0.10 0.82 0.10Reference Only Spec No. JEFL243E-0004W P2/9 6.Marking No Marking. 7. Electrical Performance No. Item Specification Test Method 7.1 Common Mode Meet item 3. Measuring Frequency : 1001MHz (ref.item 10.) Impedance Measuring Equipment : KEYSIGHT 4291A or the equivalents (In case of doubt in standard condition, the heat treatment (200C,about 10 min)shall be applied. 7.2 Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage Voltage Time : 1 to 5 s Charge Current : 1 mA max.(ref.item 10.) 7.3 DC Resistance Meet item 3. Measuring current : 100mA max.(ref.item 10.) (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Resistance (I.R.) Measuring time : 1 min max. (ref.item 10.) 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 150C, 1min coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2453C Immersion Time : 31 s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 150C ,1min Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 101 s Impedance within 20% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition I.R. 100M min. for 4 to 48 h. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 3 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 55 to 10Hz for 1 min Total Amplitude : 1.5mm Testing Time : A period of 2 h in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : (t =1.0 mm). Strength Table 2 Deflection : 2 mm Speed of Applying Force : 0.5 mm / s Appearance No damaged Keeping time : 30 s DC Resistance within 30% Pressure jig Change R230 F Deflection 45 45 Product MURATA MFG.CO., LTD