Chip Monolithic Ceramic Capacitor for Automotive limited to Conductive Glue Mounting GCB155M91A223KE03 (0402, X9M:MURATA, 22000pF, DC10V) : packaging code Reference Sheet 1.Scope This product specification is applied to Chip Monolithic Ceramic Capacitor limited to Conductive Glue Mounting Type used for Automotive Electronic equipment with conductive glue mounting. 2.MURATA Part NO. System (Ex.) GCB 15 5 M9 1A 223 K E03 D (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 1.00.1 0.50.05 0.50.05 0.15 to 0.35 0.3 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X9M(MURATA) (5) Nominal Methods Rated Capacitance Capacitance (Operating Temp. coeff Temp. Range Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 200 C -50 to 15 % DC 10 V 22000 pF 10 % -55 to 200 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel D 10000 pcs./Reel PAPER W8P2 f330mm Reel J 50000 pcs./Reel PAPER W8P2 Product specifications in this catalog are as of Dec.14,2016,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GCB155M91A223KE03-01 1AEC-Q200 Murata Standard Specification and Test Methods No AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress 1 - Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Mount the capacitor on the test jig using a conductive glue. Exposure (Storage) specifications in the following table. (Refer to No.16 as for conductive glue.) Appearance No marking defects Set the capacitor for 1000+/-12h at 1503 (for R9) , 200+/-3 (for M9). Capacitance Within 10% Change Initial measurement Dissipation 0.2max Perform a heat treatment at 150+0/-10 for 1h and then sit Factor for 24+/-2h at room temperature. Insulation Within the specified initial value. Perform the initial measurement. Resistance Measurement after test 25 Sit for 24+/-2h at room temperature, then measure. 3 Temperature Cycling The measured and observed characteristics should satisfy the Mount the capacitor on the test jig using a conductive glue. specifications in the following table. (Refer to No.16 as for conductive glue.) Perform the 1000 cycles test according to the four heat treatments Appearance No marking defects listed in the following table. Step 1 2 3 4 Temp. Room Room Min.Operating Temp.+0/-3 Max.Operating Temp. +3/-0 ( C) Temp. Temp. Capacitance Within 7.5% Time Change 15+/-3 1 15+/-3 1 (min.) Dissipation 0.2max Initial measurement Factor Perform a heat treatment at 150+0/-10 for 1h and then sit for 24+/-2h at room temperature. Perform the initial measurement. Insulation Within the specified initial value. Measurement after test Resistance Sit for 24+/-2h at room temperature, then measure. 25 4 Destructive No defects or abnormalities Per EIA-469 Physical Analysis 5 Moisture Resistance specifications in the following table. Mount the capacitor on the test jig using a conductive glue. (Refer to No.16 as for conductive glue.) Apply the 24h heat (25 to 65 ) and humidity (80 to 98%) treatment shown below, 10 consecutive times. Appearance No marking defects Humidity Humidity Temperature 8098% 8098% Humidity Humidity Humidity () 9098% 9098% 9098% 70 65 60 Capacitance Within 10% 55 50 Change 45 40 35 30 25 20 +10 - 2 15 Dissipation 0.2max 10 5 Initial measuremt Factor 0 -5 -10 One cycle 24hours 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Hours Initial measurement Insulation Within the specified initial value. Perform a heat treatment at 150+0/-10 for 1h and then sit Resistance for 24+/-2h at room temperature. 25 Perform the initial measurement. Measurement after test Perform a heat treatment at 150+0/10C for 1h and then let sit for 24+/-2h at room temperature, then measure. JEMCGS-04885B 2