Chip Monolithic Ceramic Capacitor MLSC Serial for Automotive GCD21BC71C504ME01 (0805, X7S:EIA, 0.5uF, DC16V) : packaging code Reference Sheet 1.Scope This product specification is applied to Chip Monolithic Ceramic Capacitor MLSC Serial used for Automotive Electronic equipment. 2.MURATA Part NO. System (Ex.) GCD 21 B C7 1C 504 M E01 L (1)L/W (2)T (3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control (8)Packaging Code Dimensions Dimensions Characteristics Voltage Capacitance Tolerance Code 3. Type & Dimensions (Unit:mm) (1)-1 L (1)-2 W (2) T e g 2.00.15 1.250.15 1.250.15 0.2 to 0.7 0.7 min. 4.Rated value (3) Temperature Characteristics Specifications and Test (4) (6) (Public STD Code):X7S(EIA) (5) Nominal Methods Rated Capacitance Capacitance (Operating Temp. coeff Temp. Range Voltage Tolerance Temp. Range) orCap. Change (Ref.Temp.) -55 to 125 C -22 to 22 % DC 16 V 0.5 uF 20 % -55 to 125 C (25 C) 5.Package mark (8) Packaging Packaging Unit f180mm Reel L 3000 pcs./Reel EMBOSSED W8P4 f330mm Reel K 10000 pcs./Reel EMBOSSED W8P4 Product specifications in this catalog are as of Mar.15,2016,and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering. Please read rating and Cautions first. GCD21BC71C504ME01-01 1AEC-Q200 Murata Standard Specification and Test Methods No AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress 1 - Electrical Test 2 High Temperature The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). Exposure (Storage) specifications in the following table. Set the capacitor for 100012h at 1503 . Set for Appearance No marking defects 242h at room temperature, then measure. Capacitance C7: Within 10 Change Dissipation C7: 0.2max Factor Insulation 50 F min. Resistance 3 Temperature Cycling The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). specifications in the following table. Perform cycle test according to the four heat treatments listed Appearance No marking defects in the following table. Set for 242h at room temperature, Capacitance C7: Within 7.5% then measure. Change Step 1 2 3 4 Dissipation C7: 0.2max Factor Temp. Room Room -55+0/-3 125+3/-0 ( C) Temp. Temp. Time 15 3 1 15 3 1 Insulation 50 F min. (min) Resistance Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/-10 for 1h and then set for 242h at room temperature. Perform the initial measurement. 4 Destructive No defects or abnormalities Per EIA-469 Phisical Analysis 5 Moisture Resistance The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). Apply the 24h heat (25 to 65 ) and humidity (80 to 98%) specifications in the following table. treatment shown below, 10 consecutive times. Appearance No marking defects Set for 242h at room temperature, then measure. Capacitance C7: Within 10% Humidity Humidity Temperature 8098% 80 98% Change Humidity Humidity Humidity () 9098% 9098% 9098% 70 Dissipation C7: 0.2max 65 Factor 60 55 50 45 40 35 30 Insulation 50 F min. 25 +10 20 Resistance - 2 15 10 5 Initial measuremt 0 -5 -10 One cycle 24hours 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Hours Measurement after test for high dielectric constant type Perform a heat treatment at 150+0/10C for 1h and then let sit for 242h at room temperature, then measure. 6 Biased Humidity The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). specifications in the following table. Apply the rated voltage and 1.3+0.2/-0vdc (add 6.8k resister) Appearance No marking defects at 853 and 80 to 85% humidity for 100012h. Capacitance C7: Within 10% Remove and set for 242h at room temprature, then measure. Change The charge/discharge current is less than 50mA. Dissipation C7: 0.2 max Factor Measurement after test for high dielectric constant type Perform a heat treatment at 150+0/10C for 1h and then let Insulation 5 F min. sit for 242h at room temperature, then measure. Resistance JEMCGS-04857 2