LQH2HPN6R8MG0L Murata

Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) 11 Data Sheet Chip Inductor (Chip Coil) Power Inductor (Wire Wound Type) LQH2HP G0 Series (1008 Size) c Dimensions c Packaging Code Packaging Minimum Quantity Polarity Marking L 180mm Embossed Tape 3000 2.00.2 2.50.2 0.850.3 0.850.3 (in mm) c Rated Value (p: packaging code) Rated Current Rated Current Self Resonance Part Number Inductance DC Resistance (Based on Inductance Change) (Based on Temperature Rise) Frequency (min.) LQH2HPN2R2MG0p 2.2H 20% 1640mA 1000mA 0.17ohm 20% 80MHz LQH2HPN3R3MG0p 3.3H 20% 1290mA 810mA 0.27ohm 20% 65MHz LQH2HPN4R7MG0p 4.7H 20% 1000mA 700mA 0.36ohm 20% 60MHz LQH2HPN6R8MG0p 6.8H 20% 800mA 590mA 0.5ohm 20% 10MHz LQH2HPN100MG0p 10H 20% 700mA 490mA 0.73ohm 20% 10MHz LQH2HPN220MG0p 22H 20% 490mA 340mA 1.6ohm 20% 10MHz LQH2HPN101MG0p 100H 20% 210mA 130mA 10ohm 20% 5MHz Test Frequency: 1MHz Class of Magnetic Shield: Magnetic shield of magnetic powder in resin Operating Temperature Range (Self-temperature rise is not included): -40 to +85C Only for re ow soldering. c Notice (Rated Current) Inductance will be more than the value which is 30% down from minimum rated Inductance value. When Rated Current is applied to the Products, self-generation of heat will rise to 40C or less. Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, its speci cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical speci cations because there is no space for detailed speci cations. Therefore, please approve our product speci cations or transact the approval sheet for product speci cations before ordering. 2012.5.10 Inductors (Coils) > Chip Inductor (Chip Coil) > Power Inductor (Wire Wound Type) 22 Data Sheet Continued from the preceding page. c Inductance-Frequency Characteristics (Typ.) c Inductance-Current Characteristics (Typ.) 1000 1000 100H 100 100 100H 10H 22H 6.8H 10H 22H 6.8H 4.7H 4.7H 10 10 3.3H 3.3H 2.2H 2.2H 1 1 0.1 0.1 0.1 1 10 100 1000 10 100 1000 10000 Frequency (MHz) Current (mA) c Temperature Rise Characteristics (Typ.) 50 10H 4.7H 2.2H 3.3H 100H 40 6.8H 22H 30 20 10 0 0 350 700 1050 1400 Current (mA) c Caution/Notice Caution (Rating) Notice Do not use products beyond the rated current as Solderability of Tin plating termination chip might be this may create excessive heat. deteriorated when low temperature soldering pro le where peak solder temperature is below the Tin melting point is used. Please con rm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, its speci cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical speci cations because there is no space for detailed speci cations. Therefore, please approve our product speci cations or transact the approval sheet for product speci cations before ordering. 2012.5.10