LQH32DZ220K53L Murata

Spec No.JELF243A-9019B-01 P.1/7 Reference Only CHIP COILCHIP INDUCTORSLQH32DZ53L Murata Standard Reference SpecificationAEC-Q200 1. Scope This reference specification applies to Wire Wound Chip Coil (Chip Inductors) LQH32DZ Series for Automotive Electronics based on AEC-Q200 except for Power train and Safety. 2. Part Numbering (ex) LQ H 32 D Z 1R0 M 5 3 L Product ID Structure Dimension Applications Category Inductance Tolerance Features Electrode Packaging (LW) and L:Taping Characteristics 3. Rating Operating Temperature Range. -40 to +105C Storage Temperature Range. -40 to +105C Self Inductance DC Rated Customers MURATA Resonant ESD Resistance Current Tolerance Part Number Part Number Frequency 5A8kV (H) (mA) () (%) (MHz min) LQH32DZ1R0M53L 1.0 0.06030% 100 1000 LQH32DZ2R2M53L 2.2 0.09730% 64 790 LQH32DZ3R3M53L 3.3 M:20 0.1230% 50 710 LQH32DZ4R7M53L 4.7 0.1530% 43 650 LQH32DZ6R8M53L 6.8 0.2530% 32 540 LQH32DZ100K53L 10 0.3030% 26 450 5A LQH32DZ150K53L 15 0.5830% 26 300 LQH32DZ220K53L 22 0.7130% 19 250 LQH32DZ330K53L 33 K:10 1.130% 17 200 LQH32DZ470K53L 47 1.330% 15 170 LQH32DZ680K53L 68 2.230% 12 130 LQH32DZ101K53L 100 3.530% 10 100 4. Testing Conditions Unless otherwise specified In case of doubt Temperature : Ordinary Temperature / 15C to 35C Temperature : 20C 2C Humidity : Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH) Atmospheric Pressure : 86kPa to 106 kPa 5. Appearance and Dimensions (No marking) 2.50.2 3.60.2 2.53.20.20.2 A A 3.20.2 2.50.2 3.20.3 4.50.3 A : 2.8max. No Marking Unit Mass (Typical value) 0.045g (in mm) 0.90.3 0.90.3 1.0 min. 1.0 min. 1.0 min. MURATA MFG.CO., LTD 1.550.15 2.60.2Spec No.JELF243A-9019B-01 P.2/7 Reference Only 6. Electrical Performance No. Item Specification Test Method 6.1 Inductance Inductance shall meet item 3. Measuring Equipment: KEYSIGHT 4192A or equivalent Measuring Frequency:1MHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment:Digital multi meter 6.3 Self Resonant S.R.F shall meet item 3. Measuring Equipment : Frequency(S.R.F) KEYSIGHT E4991A or equivalent 6.4 Rated Current Self temperaturer rise shall be The rated current is applied. limited to 20C max. Inductance Change : within 10% 7. AEC-Q200 Requirement 7.1 Performance (based on Table 5 for Magnetics(Inductors / Transformer) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No Stress Test Method 3 High 1000hours at 105 deg C Meet Table A after testing. Temperature Set for 24hours at room temperature, Table A Exposure then measured. Appearance No damage Inductance change Within 5% 4 Temperature Cycling 1000cycles Meet Table A after testing. -40 deg C to + 105deg C Set for 24hours at room temperature,then measured. 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. unpowered.. 8 Operational Life Apply 105 deg C 1000 hours Meet Table A after testing. Set for 24hours at room temperature, then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 5 No defects (Style and Dimensions) 12 Resistance Per Not Applicable to Solvents MIL-STD-202 Method 215 13 Mechanical Shock Per MIL-STD-202 Meet Table A after testing. Method 213 100gs/6ms/Half sine 14 Vibration 5g s for 20 minutes, Meet Table A after testing. 12cycles eah of 3 orientations Test from 10-2000Hz. 12cycles each of 3 orientations 15 Resistance No-heating Meet Table A after testing. to Soldering Heat Solder temperature 260C+/-5 deg C Immersion time 10s MURATA MFG.CO., LTD