NFG0NCN162HL3D Murata

Reference Only Spec No. JEFL243D-0011C-01 P1/10 Common Mode Noise Filter NFG0NCNHL3 Reference Specification 1. Scope This reference specification applies to Common Mode Noise Filter NFG0NCN Series for differential signal interface in Electronics. 2. Part Numbering (ex.) NF G 0N C N 162 H L 3 D (10) (1) (2) (3) (4) (5) (6) (7) (8) (9) (1) Common Mode Noise Filter (6) Common Mode Insertion Loss Characteristic Resonant Frequency(Typ.) (2) Structure G : Monolithic Type (7) Circuit H : Characteristic Impedance 100 system (3) Dimension (8) Features (4) Type (9) Number of Line (5) Category N : General Use (10) Packaging Code D : Taping / B : Bulk *Bulk packing also available. (A product is put in the plastic bag under the taping conditions.) 3. Rating Common Mode Common Mode Customer MURATA Insertion Loss Characteristic Impedance (dB Typ.) Part Number Part Number ( ) at 100MHz 800MHz 1G Hz 1.6GHz NFG0NCN162HL3D 2525% 19 22 29 DC Insulation Rated Rated Withstanding Cut off MURATA Resistance Resistance Current Voltage Voltage Frequency Part Number (Rdc) (I.R.) (mA) (V(DC)) (V(DC)) (GHz Typ.) () (M min.) NFG0NCN162HL3D 100 5 12.5 1.85 25% 10 4 Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions Equivalent Circuits No polarity. Unit Mass(Typical value) 0.00087g 6.Marking No Marking. MURATA MFG.CO., LTD Reference Only Spec No. JEFL243D-0011C-01 P2/10 7. Electrical Performance No. Item Specification Test Method Common Mode Meet item 3. Measuring Frequency : 100MHz (ref.item 10.) 7.1 Impedance Measuring Equipment : KEYSIGHT4291A or the equivalents (In case of doubt in standard condition, the heat treatment(200C, about 10 minutes)shall be applied. Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage 7.2 Voltage Time : 1 to 5 s Charge Current : 1 mA max.(ref.item 10.) 7.3 DC Resistance Meet item 3. Measuring current : 20mA max.(ref.item 10.) (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Resistance (I.R.) Measuring time : 1 min max. (ref.item 10.) 8.Mechanical Performance It shall be soldered on the 6 Layer substrate (t1.0mm).except Solderability Test shall be done using P.C.B., Flux, Solder and Soldering condition which are specified in item 16 except the case of being specified special condition. No. Item Specification Test Method 8.1 Bonding Strength Products shall not be damaged Applying Force: 2N after tested as test method. Applying Time : 5s Bending Strenght Test substrate: glass-epoxy substrate (100 mm 40 mm 8.2 1.0 mm) Deflection : 2mm Speed of Applying Force : 1.0mm/s Keeping Time : 20s Pressure jig R230 F Deflection 45 45 Product Appearance: No damage Oscillation Frequency : 10Hz to 2000Hz to 10Hz for 20min 8.3 Vibration Total amplitude 3.0mm or Acceleration amplitude 196 m/s2 whichever is smaller. Testing Time : A period of 2h in each of 3 mutually perpendicular directions.(Total 6h) The electrodes shall be at least 95% Flux : Ethanol solution of rosin,25(wt)% 8.4 Solderability covered with new solder coating. Pre-Heating : 150C, 60s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 245C3C Immersion Time : 3s MURATA MFG.CO., LTD