NFL18SP307X1A3D Murata

Reference Only Spec. No. JENF243D-0003K-01 P1/ 8 Chip EMIFIL LC Combined Monolithic NFL18SPX1A3 Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Monolithic Type NFL18SP Series. 2. Part Numbering NF L 18 SP 157 X 1A 3 D Product ID Structure Dimension Features Cut-off Frequency Characteristics Rated Voltage Electrode Packaging Code (LW) (D : Taping / B : Bulk) 3. Rating DC Insulation Cut-off Inductance Rated Rated Withstanding Customer MURATA Capacitance Resistance Resistance Frequency (L) Voltage Current Voltage Part Number Part Number pF MHz nH V(DC) mA(DC) V(DC) max. M min. NFL18SP157X1A3D 150 3420% 10020% NFL18SP157X1A3B NFL18SP207X1A3D 200 2420% 8020% 3.0 NFL18SP207X1A3B 1000 10 100 30 NFL18SP307X1A3D 300 1920% 6020% NFL18SP307X1A3B NFL18SP507X1A3D 500 1120% 3820% 2.0 NFL18SP507X1A3B Operating Temperature : -55C to +125C (Includes self-heating.) Storage Temperature : -55C to +125C 4. Standard Testing Condition < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. / 15 C to 35 C Temperature : 20 C 2 C Humidity : Ordinary Humidity / 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH) Atmospheric pressure : 86 kPa to 106 kPa 5. Style and Dimensions 0.30.1 0.40.1 0.30.1 0.80.1 Equivalent Circuits Out put Input (1) (3) 0.2min. 0.150.1 GND 1.60.1 (2) (2) No Polarity (1) (3) :Electrode Unit Mass (Typical value) 0.004g (1) (3) (in mm) (2) 0.150.1 Insertion Loss Characteristics (I.L.) (Typ.) (50system) MURATA MFG.CO., LTD. 0.60.1Reference Only Spec. No. JENF243D-0003K-01 P2/ 8 6. Marking No marking 7. Electrical Performance No. Item Specification Test Method 7.1 Capacitance Meet item 3. Frequency : 10.1MHz (Cap.) Voltage : 10.2V(rms) Frequency : 101MHz 7.2 Inductance (L) Voltage : 10.2V(rms) 7.3 DC Resistance Measured with 10mA max. (Rdc) Measured between terminal (1)-(3). (ref. Item5) 7.4 Insulation Voltage : Rated Voltage Resistance(I.R.) Time : 1 minutes max. 7.5 Withstanding Products shall not be damaged. Test Voltage : 30V(DC) Voltage Time : 1 to 5 s Charge Current : 50 mA max. 8. Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Dimensions Calipers. 8.2 Solderability Electrodes shall be at least 90% Flux : Ethanol solution of rosin, 25(wt)% covered with new solder coating. Pre-heat : 150 10C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 240 3C Immersion Time : 31 s Immersion and emersion rates : 25mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin, 25(wt)% soldering heat Table 1 Pre-heat : 150 10C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 270 5C Cap. Change within 5% Immersion Time : 10 1 s L Change within 5% Immersion and emersion rates : 25mm / s I.R. meet item 3 8.4 Bending Meet Table 2. It shall be soldered on the glass-epoxy substrate Strength (t = 1.0mm). Table 2 Deflection : 2.0 mm Appearance No damaged Keeping Time : 30 s Cap. Change within 5% Pressure jig R230 F Deflection 45 45 Product (in mm) 8.5 Drop Products shall be no failure after It shall be dropped on concrete or steel board. tested. Method : Free fall Height : 1m Attitude from which the product is dropped : 3 directions The Number of Time : 3 times for each direction (Total 9 times) MURATA MFG.CO., LTD.