NFZ18SM251SZ10D Murata

Reference Only Spec. No. JENF243J-9104-01 P.1/8 Chip Noise Filter NFZ18SMSZ10 REFERENCE SPECIFICATION AEC-Q200 1.Scope This reference specification applies to Chip Noise Filter NFZ18SM SZ10 Series for Automotive Electronics based on AEC-Q200 except for Power train and Safety. 2.Part Numbering NF Z 18 S M 121 S Z 1 0 D Product ID Structure Dimension Characteristics Typical Impedance Performance Category Numbers special Packaging (LW) at 100MHz of speci- D:Taping Circuit fication *B: BULK *B: Bulk packing also available 3.Rating+ Operating Temperature : -55C to +125C Storage Temperature : -55C to +125C Impedance ( ) DC Resistance *1 *1 Rated (at 100MHz) ( max.) Current ESD Rank (refer to below (refer to below comment) Customer MURATA (mA) 6:25kV comment) Part Number Part Number Initial Values Values After *2 *2 Typical 85 125 Testing 12025% 120 1250 1100 0.14 0.24 NFZ18SM121SZ10D 25025% NFZ18SM251SZ10D 250 1100 1000 0.19 0.29 6 50025% 500 950 850 NFZ18SM501SZ10D 0.25 0.35 70025% 700 800 800 NFZ18SM701SZ10D 0.29 0.39 *1 Standard Testing Conditions Unless otherwise specified In case of doubt Temperature : Ordinary Temp. (15 C to 35 C ) Temperature : 20C2 C Humidity : Ordinary Humidity (25%(RH) to 85%(RH)) Humidity : 60%(RH) to 70%(RH) Atmospheric pressure : 86kPa to 106kPa Rated current *2 As for the rated current, at 85C Rated Current derated as right figure depending on the operating temperature. Rated current at 125C 0 85 125 Operating Temperature (C) 4. Appearance and Dimensions 1.6 0 .15 0.80 . 15 Equivalent Circuit 0.80.15 Resistance element becomes 0.4 0 . 2 () dominant at high frequencies. Electrode : (in mm) Unit Mass (Typical value) 0.005g MURATA MFG.CO., LTD. Rated Current (A)Reference Only Spec. No. JENF243J-9104-01 P.2/8 5.Marking No marking. 6.Electrical Performance No. Item Specification Test Method 6.1 Impedance Meet item 3. Measuring Frequency : 100MHz1MHz Measuring Equipment : Agilent 4291A or the equivalent Test Fixture : Agilent 16192A or the equivalent 6.2 DC Resistance Meet item 3. Measuring Equipment : Digital multi meter 7. AEC-Q200 Requirement 7.1 Mechanical Performance(based on Table 13 for FILTER EMI SUPPRESSORS/FILTERS) AEC-Q200 Rev.D issued June. 1 2010 AEC-Q200 Murata Specification / Deviation No. Stress Test Method 3 High 1000hours at 125 deg C Meet Table A after testing. Temperature Set for 24hours at room Table A Exposure temperature, then measured. Appearance No damage Impedance Within 30% Change (at 100MHz) DC Meet item 3. Resistance 4 Temperature Cycling 1000cycles Meet Table A after testing. -55 deg C to +125 deg C Set for 24hours at room temperature, then measured. 5 Destructive Per EIA469 No defects Physical Analysis No electrical tests 7 Biased Humidity 1000hours at 85 deg C, 85%RH Meet Table A after testing. Apply max rated current. Meet Table A after testing. 8 Operational Life Apply 125 deg C 1000hours Rated current at 125 is derated Set for 24hours at room (Refer to 3.Rating) temperature, then measured 9 External Visual Visual inspection No abnormalities 10 Physical Dimension Meet ITEM 4 No defects Style and Dimensions 12 Resistance to Solvents Per MIL-STD-202 Not Applicable Method 215 13 Mechanical Shock Per MIL-STD-202 Method 213 Meet Table A after testing. Condition F 1500g s (14.7N)/0.5ms/ Half sine 14 Vibration 5g s(0.049N) for 20 minutes, Meet Table A after testing. 12cycles each of 3 orientations Test from 10-2000Hz. MURATA MFG.CO., LTD.