NFZ2MSD600SN10L Murata

Reference Only Spec No.JETE243A-0045-01 P 1/8 CHIP NOISE FILTER NFZ2MSDSN10L SPECIFICATION REFERENCE SPECIFICATION 1. Scope This reference specification applies to NFZ2MSDSN10L, Chip Noise Filter. 2.Part Numbering (ex) NF Z 2M SD 100 S N 1 0 L Numbers Special Product Typical Structure Dimension Characteristics Performance Category Of Speci- Packaging ID Impedance Circuit fication (LW) at 10MHz (T) L: 180Taping 3.Rating Operating Temperature Range (Ambient temperature Self-temperature rise is not included) -40 to +85C (Product temperature Self- temperature rise is included) -40 to +125C Storage Temperature Range. -40 to +85C Absolute maximum voltage 20V DC Impedance DC Resistance *1 Rated Current Customer Murata at 10MH Max Part Number Part Number () Tolerance (m ) A NFZ2MSD100SN10L 10 20 5.2 NFZ2MSD150SN10L 15 23 4.4 NFZ2MSD200SN10L 20 28 3.9 NFZ2MSD300SN10L 30 30% 33 3.7 NFZ2MSD600SN10L 60 54 2.7 NFZ2MSD900SN10L 90 95 2.0 NFZ2MSD131SN10L 130 144 1.5 *1: When applied Rated current to the Products, self temperature rise shall be limited to 40 max. 4. Testing Conditions (Standard atmospheric conditions) <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature (15 to 35C) Temperature : 20 2C Humidity : Ordinary Humidity (25 to 85 %(RH)) Humidity : 60 to 70 %(RH) Atmospheric Pressure : 86 to 106 kPa 5.Appearance and Dimensions no marking (in mm) Unit Mass (Typical value) 0.0188g MURATA MFG.CO., LTD Reference Only Spec No.JETE243A-0045-01 P 2/8 6. Electrical Performance No. No. Item Specification 6.1 Impedance Meet item 3. Measuring Equipment: KEYSIGHT 4287A or equivalent (0.5V) Measuring Frequency: 10MHz 6.2 DC Resistance Measuring Equipment: Digital multi meter 7. Mechanical Perdormance No. Item Specification Test Method 7.1 Shear Test Chip coil shall not be damaged. It shall be soldered on the substrate. Applying Force(F) : 10N Hold Duration: 5s 7.2 Bending Test Chip coil shall not be damaged. Substrate: Glass-epoxy substrate (100401.0mm) Speed of Applying Force: 0.5mm / s Deflection: 2mm Hold Duration: 20s (in mm) 7.3 Vibration Chip coil shall not be damaged. It shall be soldered on the substrate. Oscillation Frequency : 10 to 2000 to 10Hz for 20 minutes Total amplitude : 1.5 mm or Acceleration amplitude 2 98m/s whichever is smaller. Testing Time: A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) 7.4 Solderability The wetting area of the electrode shall Flux:Ethanol solution of rosin,25(wt)% be at least 90% covered with new (Immersed for 5s to 10s) solder coating. Solder : Sn-3.0Ag-0.5Cu Pre-Heating:15010C / 60 to 90s Solder Temperature:2455C Immersion Time:3 s 7.5 Resistance to Appearance:No damage Reflow soldering method Soldering Impedance Change : within 30% Flux: Ethanol solution of rosin,25(wt)% Heat Solder: Sn-3.0Ag-0.5Cu Pre-Heating: 150~180C / 9030s Solder Temperature: 230C min / 3010s Peak Temperature: 250+5/-0C Reflow times: 2 times max Test board shall be 0.8 mm thick. Base material shall be glass epoxy resin. Then measured after exposure Standard atmospheric conditions for 1~2 hours. MURATA MFG.CO., LTD