NMF0505DC Murata

NMF Series www.murata-ps.com Isolated 1W Regulated Single Output DC-DC Converters SELECTION GUIDE Package Order Code Style V V mA mW % pF kHrs NMF0505DC 5 5 100 500 50 37 1307 DIP NMF0515DC 5 15 67 1000 62 52 316 DIP FEATURES NMF0505SC 5 5 100 500 50 37 1307 SIP Output regulation <1.5% NMF0512SC 5 12 83 1000 62 46 512 SIP NMF0515SC 5 15 67 1000 62 52 316 SIP Output programmable NMF1205DC 12 5 100 500 50 62 456 DIP Single isolated output NMF1215DC 12 15 67 1000 62 108 218 DIP NMF1205SC 12 5 100 500 50 62 456 SIP SIP & DIP package style NMF1212SC 12 12 83 1000 62 98 290 SIP 1kVDC isolation Hi Pot Test NMF1215SC 12 15 67 1000 62 108 218 SIP 5V,12V & 24V input NMF2405DC 24 5 100 500 50 69 843 DIP NMF2405SC 24 5 100 500 50 69 843 SIP 5V,12V & 15V output NMF2412SC 24 12 83 1000 62 129 422 SIP SMD construction NMF2415SC 24 15 67 1000 62 151 279 SIP Recommended No external components required Alternative MTTF up to 2.4 million hours NMF0509DC 5 9 100 900 62 42 825 DIP Contact Murata NMF0509SC 5 9 100 900 62 42 825 SIP Contact Murata DESCRIPTION NMF1209DC 12 9 100 900 62 82 379 DIP Contact Murata NMF1209SC 12 9 100 900 62 82 379 SIP Contact Murata The NMF series of DC-DC converters is used NMF4805DC 48 5 100 500 50 51 200 DIP Contact Murata where a tightly regulated supply is required. They NMF4809DC 48 9 100 900 62 86 283 DIP Contact Murata are ideal for situations where the input voltage is NMF4812DC 48 12 83 1000 62 108 162 DIP Contact Murata not tightly controlled. The output trim pin makes NMF4815DC 48 15 67 1000 62 127 135 DIP Contact Murata the device particularly suitable for applications requiring a programmable output voltage. The 5V NMF4805SC 48 5 100 500 50 51 200 SIP Contact Murata output version can be used to give a regulated NMF4809SC 48 9 100 900 62 86 283 SIP Contact Murata output, adjustable between 1.2V and 5.0V with a NMF4812SC 48 12 83 1000 62 108 162 SIP Contact Murata single resistor. NMF4815SC 48 15 67 1000 62 127 135 SIP Contact Murata NMF0512DC 5 12 83 1000 62 46 512 DIP NMF0512SC NMF1212DC 12 12 83 1000 62 98 290 DIP NMF1212SC NMF2409DC 24 9 100 900 62 106 613 DIP Contact Murata NMF2409SC 24 9 100 900 62 106 613 SIP Contact Murata NMF2412DC 24 12 83 1000 62 129 422 DIP NMF2412SC NMF2415DC 24 15 67 1000 62 151 279 DIP NMF2415SC When operated with additional external load capacitance the rise time of the input voltage will determine the maximum external capacitance value for guaranteed start up. The slower the rise time of the input voltage the greater the maximum value of the additional external capacitance for reliable start up. 1. Calculated using MIL-HDBK-217F with nominal input voltage at full load. 2. Supply voltage must be discontinued at the end of the short circuit duration. For full details go to All specications typical at TA=25C, nominal input voltage and rated output current unless otherwise specied. www.murata-ps.com/rohs www.murata-ps.com/support KDC NMF.H01 Page 1 of 5 Nominal Input Voltage Output Voltage Output Current Power Out Efciency Isolation Capacitance 1 MTTFNMF Series Isolated 1W Regulated Single Output DC-DC Converters ABSOLUTE MAXIMUM RATINGS 2 Short-circuit protection 1 second Lead temperature 1.5mm from case for 10 seconds 260C Input voltage VIN, NMF05 types 7V Input voltage VIN, NMF12 types 15V Input voltage VIN, NMF24 types 28V INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Continuous operation, 5V input types 4.75 5 5.25 Voltage range Continuous operation, 12V input types 11.4 12 12.6 V Continuous operation, 24V input types 22.8 24 25.2 OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Voltage set point accuracy 100% load 5% Rated power TA= 0C to 70C, see derating graph 1W Line regulation High VIN to low VIN 0.25 %/% Load regulation 10% load to rated load 0.9 1.5 % Ripple & noise BW=DC to 20MHz, all output types 60 mV p-p ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Isolation test voltage Flash tested for 1 second 1000 VDC Resistance Viso= 500VDC 0.1 G GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Switching frequency All input types 90 kHz TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Specication All output types 0 70 Case temperature above ambient 38 C Storage -55 150 Cooling Free air convection OUTPUT VOLTAGE ADJUSTMENT (for 5V output variants) The trimming (adjust) input on the device allows output voltage adjustment from 1.2V to 3.3VDC by using a resistor as shown here. The table below provides RTRIM values for the most commonly required output voltages. For applications not requiring the TRIM function, this pin must be left unconnected for normal regulated output. VOUT SET (V) RTRIM () +VIN VOUT 1.2 0 1.5 64 2.0 224 TRIM NMF 2.1 263 2.2 304 RTRIM 2.5 448 -VIN -VOUT 3.3 1071 www.murata-ps.com/support KDC NMF.H01 Page 2 of 5