RFM products are now Murata products. RF3210D Ideal Front-End Filter for Domestic Wireless Receivers Low-Loss, Coupled-Resonator Quartz Design Pb Simple External Impedance Matching 303.825 MHz Complies with Directive 2002/95/EC (RoHS) SAW Filter The RF3210D is a low-loss, compact, and economical surface-acoustic-wave (SAW) filter designed to provide front-end selectivity in 303.825 MHz receivers. Receiver designs using this filter include superheterodyne with 10.7 MHz or lower IF frequencies, direct conversion receivers and superregenerative receivers. This coupled-resonator filter (CRF) uses selective null placement to provide suppression, typically greater than 40 dB, of the LO and image spurious responses of superhet receivers with 10.7 MHz IF. Muratas advanced SAW design and fabrication technology is utilized to achieve high performance and very low loss with simple external impedance matching. SM3838-8 Case 3.8 x 3.8 Characteristic Sym Notes Minimum Typical Maximum Units Center Frequency 25C f 1, 2, 3 303.825 MHz C IL Minimum Insertion Loss, 303.620 to 303.980 MHz 1, 3 1.6 2.5 dB MIN Passband Loss Relative to IL : MIN 303.595 to 304.025 MHz 1.0 3.0 1 dB 303.535 to 304.085 MHz 1.5 6.0 BW 3 dB Bandwidth 1, 3 500 650 800 kHz 3 Attenuation Relative to IL : MIN 10 to 260 MHz 45 55 260 to 297 MHz 35 45 297 to 302.5 MHz 11.5 15 1 dB 304.8 to 320 MHz 14 20 320 to 400 MHz 37 40 400 to 1000 MHz 45 55 2 Frequency Temperature Coefficient FTC 0.032 ppm/C Frequency Aging, Absolute Value During the First Year fA 10 ppm/yr Impedance F Input Z =R llC Z 11.7 K ll 1.8 pF C IN IN IN IN 1 Output Z =R llC Z 6.63 K ll 2.2 pF OUT OUT OUT OUT Lid Symbolization (Y=year WW=week D=day of week) 675 // YWWS Standard Reel Quantity Reel Size 7 Inch 500 Pieces/Reel 9 Reel Size 13 Inch 3000 Pieces/Reel CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 test system with VSWR < 1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, f . Note that insertion loss and bandwidth and passband shape are dependent on c the impedance matching component values and quality. 2. The frequency f is defined as the midpoint between the 3 dB frequencies. c 3. Where noted specifications apply over the entire specified operating temperature range of -40 C to +90 C. 4. The turnover temperature, T , is the temperature of maximum (or turnover) frequency, f . The nominal frequency at any case temperature, T , may be calculated from: O o c 2 f= f 1 - FTC (T -T ) . o o c 5. Frequency aging is the change in fc with time and is specified at +65 C or less. Aging may exceed the specification for prolonged temperatures above +65 C. Typically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years. 6. The design, manufacturing process, and specifications of this device are subject to change without notice. 7. One or more of the following U.S. Patents apply: 4,54,488, 4,616,197, and others pending. 8. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. 9. Tape and Reel Standard Per ANSI/EIA 481. 10. This product complies with directive 2002/95/EC of the European Parlament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2010-2015 by Murata Electronics N.A., Inc. RF3210D (R) 4/7/15 Page 1 of 2 www.murata.com Rating Value Units Input Power Level 10 dBm DC Voltage 12 VDC Storage Temperature -40 to +125 C Operable Temperature Range -40 to +125 C Soldering Temperature, 10 seconds / 5 cycles maximum 260 C Electrical Connections C E B 8 8 Pin Connection H 1 7 7 1 1 Input A 2 6 6 2 G 2 Input Ground 3 Ground 3 5 5 3 4 Case Ground 5 Output 4 4 D F 6 Output Ground 7 Ground 8 Case Ground Matching Circuit to 50 Case Dimensions mm Inches Dimension Min Nom Max Min Nom Max A 3.6 3.8 4.0 0.14 0.15 0.16 B 3.6 3.8 4.0 0.14 0.15 0.16 C 1.00 1.20 1.40 0.04 0.05 0.055 D 0.95 1.10 1.25 0.033 0.043 0.05 E 0.90 1.0 1.10 0.035 0.04 0.043 F 0.50 0.6 0.70 0.020 0.024 0.028 G 2.39 2.54 2.69 0.090 0.100 0.110 H 1.40 1.75 2.05 0.055 0.069 0.080 Optional Electrical Connections Optional Matching Circuit to 50 Pin Connection 1 Input Ground 2 Input 3 Ground 4 Case Ground 5 Output Ground 6 Output 7 Ground 8 Case Ground 2010-2015 by Murata Electronics N.A., Inc. www.murata.com RF3210D (R) 4/7/15 Page 2 of 2